Tuesday, December 5, 2023
HomeBathBathtub Pop Up Drain Stopper

Bathtub Pop Up Drain Stopper

How Does A Pop

Bathroom Repair : How to Repair a Pop-Up Tub Drain Stopper

Pop-up drain plugs are arguably the most common bathtub stoppers in the market. These mechanical tools leverage a system of levers and links to move a drain plug up and down to create a watertight seal for the bathtub.

Anyone can operate a pop-up drain you dont need to be a plumbing expert. The device comes with a simple design and operates by the same lever on the overflow platelike in a trip-lever stopper.

When you press down on the center of the pop-up drain and twist it, the stopper will lock in place and allow water to drain out. If you want to open the drain, firmly push the center and twist it in the opposite direction.

How To Fix A Lift

A trip-lever drain stopper that uses a lift-bucket plunger can be identified by the absence of a pop-up stopper in the drain opening. When problems occur with this type of drain, it is for one of two reasons:

  • The plunger has become stuck in the overflow tube and will not move up and down freely.
  • The rod linking the trip lever to the plunger isn’t adjusted properly, creating a situation in which the lift bucket plunger doesn’t drop down enough to completely seal the drainpipe opening.

How To Fix A Sticky Trip

Aaron Stickley is a licensed plumber with 15 years of experience in commercial, new residential plumbing, and residential service and repair. He started his own residential service and repair plumbing business. Aaron’s articles about plumbing on The Spruce span four years.

The Spruce / Christopher Lee Foto

  • Skill Level: Beginner
  • Estimated Cost: $0 to $20

Any bathtub drain stopper that doesn’t do its job is an annoying inconvenience. Usually, the problem is easy to fix, though the procedures vary depending on what type of bathtub stopper you have. Some drains have stoppers that are spring-loaded, operated by a push of the toe or hand, while others use a trip-lever mounted on the bathtub’s overflow plate. A trip-lever drain stopper is more tricky than most to fix, due to its somewhat complicated mechanism.

Don’t Miss: Toilet Drains Slow And Gurgles

Understanding How Bath Plugs Work

Sometimes referred to as a bath stopper, a bathtub plug works to prevent water in the tub from leaking through the drain hole. This simple device covers the hole above the bathtub drain, creating a watertight seal and allowing the tub to get filled.

You can shop for a variety of bathtub drain stoppers on the market, each featuring a unique style, size, and material. The most common bath plugs include lift-and-turn, trip-lever, push-and-pull, toe-touch, flip-it, and pop-up.

While all work slightly different from one another, they perform the same purposeretaining water in the bathtub for the desired time and allowing the tub to get emptied again.

Most plugs come equipped with a handle or pull chain that makes it easier to unplug when emptying your tub after a good soak.

Despite their durable nature, bathtub drain stoppers often wear and tear after many years of use. As a result, they end up failing to prevent water from escaping your bathtub. When this happens, you might need to invest in a replacement.

But in case of an emergency, there are several DIY methods you can try at home to keep water in your bathtub.

How To Fix A Sink Pop

43mm Bathtub Drain Stopper Bathroom Bath Tub Sink Waste Pop

Water may leak or refuse to drain around a sink pop-up for a number of reasons. If your sink pop-up wont pop up or seat properly, fixing it is quite easyusually just a matter of adjusting a few parts. The culprit is often a buildup of hair around the base of the stopper or the pivot rod mechanism. Or, the clevis may be out of adjustment .

You May Like: Interior French Drain Pros And Cons

You Have Clogged Drain Pipes

Of course, the most common reason why a bathtub wont drain is due to clogged pipes. Over time, nearly all bathtub drains will develop clogs. These are most commonly caused by a combination of:

  • Shaving cream or gel
  • Shampoo and conditioner suds

These mix with the water during a bath or shower and they can solidify in the drain. Sometimes even small items like shampoo bottle caps or razor shields will sneak through the drain openings.

If these clogs are located near the top of the drain opening, you may be able to unclog it on your own. You will likely need to unscrew the drain opening to pull up whatever is clogging it. However, this needs to be done with care, as you could accidentally push the clog further down the pipe.

How To Fix A Pop

A trip-lever drain that operates a pop-up stopper uses a slightly different mechanism. Rather than a lift-bucket plunger that seals a drain opening at the bottom of the overflow tube, there is a spring at the end of the connecting rod. This spring pushes down on a pivot arm that levers the pop-up stopper up into an open position when the trip lever is moved. When the trip lever is moved to the closed position, gravity allows the stopper to drop back down and seal the drain opening.

Problems with this type are usually evident when the pop-up stopper fails to push up enough to open the bathtub drainit wants to stay in the closed position constantly. This is usually because the connecting rod attached to the trip lever has become shortened from use.

Don’t Miss: Ge Washer Drain And Spin Cycle Not Working

Easy Steps On How To Remove Flip

This form of stopper requires special handling because it is fixed to a linkage arm that must be extracted simultaneously from the opening.

  • Move the rotating dial to the open setting.
  • Gently remove the stopper from the drain opening and use wiggling movements to remove the whole arm linkage from the same opening.
  • Wipe off any grime from the pop up stopper and rocker arm. For lime buildups on the latter, use vinegar or commercial lime cleaners.
  • Restore some shine by polishing the stopper with commercial chrome polish. You can also use a homemade mixture of lemon and vinegar for the same task. Next, gently fix the rocker arm into the drain until the stopper fits the opening.
  • Move the lever to check if the stopper works perfectly.
  • How To Remove A Bathtub Pop

    How to Repair a Pop-Up Tub Drain Stopper

    Its easy to remove a tub stopper to check it for mechanical problems or blockage. Youll encounter a couple of different types of bathtub pop-ups: old-style mechanisms like the one shown in our illustration above, and newer spring-loaded pop-ups.

    To remove an old-style bathtub pop-up:

  • Simply grip the stopper body and pull it out of the drain along with the hinged rocker arm.
  • Clear the stopper and rocker arm of hair and debris.
  • Check the rubber seal for damage and, if necessary, replace it. Remove the old seal and slip on a new one if needed.
  • Reinstall the stopper and rocker arm. Make sure the flange is tightly seated and in good shape.
  • For removing a newer spring-loaded bathtub pop-up, this video shows the necessary techniques:

    Also Check: Garbage Disposal Not Draining Well

    Bathtub Drain Installation: Install The New Stopper Body

    Slide in a new gasket. Then roll a pencil-sized bead of plumbers putty and press it around the underside of the new stopper body rim. Stick the jaws of 8-in. pliers into the stopper body grate and thread it into the drainpipe.

    All thats left in this how to remove a bathtub drain stopper job is to install the new bathtub drain stopper body and stopper. Slide the new rubber gasket on top of the drainpipe under the tub and insert the new drain flange with plumbers putty on it as shown here.

    Use the supplied bushing if the new threads are different from the old. Screw the stopper into the stopper body and congratulate yourself on a job well done. If youve got other bathtub issues, learn how to fix a leaking bathtub faucet.

    How To Convert A Trip

    Un-like Pop-up bathtub drain stoppers which are installed at the bottom of the tub, trip-lever bathtub stoppers are installed on the side of the bathtub. A toggle lever mounted on the overflow plate is connect to 2 link rods, which in return are connected to a plunger which is responsible for closing and opening the drain

    When you flip the toggle lever up, the plunger falls to the junction of the overflow and bathtub drainpipe therefore blocking it, allowing the bathtub to fill. Flipping the lever down lifts off the plunger and the bathtub starts to drain.

    A trip-lever bathtub stoppers plunger picks up hair, soap scum and debris from the drainpipe and that is why it gets stuck very often. Mineral deposits in the overflow drain also contribute to this problem.

    At times the plunger disconnects/breaks off from the link rods and falls at the bottom of the overflow drain. In that case your bathtub cannot drain and fishing the plunger out is not always easy.

    Replacing a trip-lever bathtub stopper with a pop-up stopper is always a good idea. Pop-up bathtub drain stoppers have fewer problems and when they do have a problem they are easier to fix than their trip-lever counterparts.

    Also Check: Vinegar And Baking Soda Drain Cleaning

    How To Replace The Old Bathtub Drain: Remove The Old Drain Parts

    This photo shows how to remove the overflow plate, the stopper body and linkage. The linkage may stick and be stubborn to remove. Grab hold of it and tug hard until it pops out. Screw on the new overflow plate once the linkage has been removed. Unscrew the overflow plate and pull the upper linkage out of the overflow pipe. Pop out the drain stopper and remove the lower linkage as well. Tug firmly when extracting both parts of the linkage because they may bind inside the overflow pipe.

    Trip Lever Drain Stopper

    Winnereco Replacement Wash Basin Pop Up Sink Drain Plug Bathtub Bounce ...

    The Trip Level Stopper stands as one of the models that have levers on the overflow plate in front of the bathtub. Here, a strainer replaces a visible pop-up stopper in the drain opening.

    Unlike the other type of bathtub drain stoppers on our list, it can be confusing when you want to take out the stopper for cleaning. This task involves taking it out of the overflow tube and plate.

    If you dont like levers, you might check out the other variant that offers a twist cover on the overflow plate. To open or close the plunger of this model, you will have to rotate the twist cover in different directions.

    Read Also: Maytag Washer Won T Drain Or Spin

    Remove The Stopper Body

    The toughest part of this how to remove a bathtub drain job is removing the old tub drain stopper body, but its all downhill after that. Remove the old stopper body as shown here. If youre having trouble unscrewing it, try heating it with a hair dryer set on high. The heat may help loosen the old plumbers putty. The old tub drain stopper body can also be cut out with a reciprocating saw and metal blade, but be very careful because its easy to cut into and damage the bathtub. Cut a notch 1/4 in. wide and deep in the old stopper body with a mini hacksaw. Check progress frequently to ensure you dont cut into the tub. Wedge a 3/4-in. cold chisel into the cutout slot and pound counterclockwise with a hammer to free the stopper body . Completely unscrew and remove the stopper body.

    Bathtub Drain Stopper Types That Wont Disappoint

    Growth Machine | 2021-05-28 09:46:55 -0400

    If there is less bathwater a few minutes later than it was when you filled the tub, your drain stopper is not operating as it should. But before you toss out the old drain stopper, learn the types of bathtub drain stoppers available. Since you will be responsible for installing, maintaining, cleaning, and using it each day, even if you need a plumber’s assistance, a little research goes a long way.

    This article will offer a detailed overview of the seven bathtub drain stopper types so you can decide which one is right for you. In addition to cost, look for ease of use, ease of installation, low maintenance, and few repair costs.

    Also Check: How To Drain Your Ear

    Install The New Overflow Cover Plate

    A bathtub overflow plate is purely for cosmetic purposes. It prevents having the big overflow opening exposed which is somewhat ugly. It also prevents foreign substances from being through down the overflow pipe especially by kids.

    Here is how to install it.

    • Choose the right orientation. An overflow cover plate has a top and bottom side. The bottom side has a slot which allows excess water to flow down the overflow pipe preventing the house from flooding. Make sure that you get the orientation right.
    • Align the 2 holes on the cover plate to the 2 holes on the bathtub and slide in the 2 screws. Tighten them in place using a screwdriver.

    And basically that is how to convert a trip-lever bathtub stopper into a pop-up bathtub stopper. A plumber would charge you upwards of $80 to do it but by following this simple process you save yourself that amount.

    How Do You Stop A Bathtub Overflow Drain

    How to Remove any Bathtub Stopper, Pop-up, Grate, or Plug

    As the name suggests, a bathtub overflow drain prevents your tub from overflowing. It allows water to flow via the overflow drain instead of spilling on the floor.

    However, most people often seal off the overflow drain to enjoy a full-body bathing experience. Overflowing also leaves behind debris and other unwanted stains that make your tub look ugly.

    Fortunately, you can address this problem by getting an overflow drain cover from the hardware stores or a custom-made seal from your nearby plumbing shop.

    Alternatively, you can replace the overflow drain with a waterproof sealant to prevent it from flowing outside. Keep in mind that this solution is more permanent, but you can always reinstall your original drain cover if the need arises.

    Don’t Miss: Underwater Boat Lights Drain Plug

    What Should I Do If I Cant Unclog The Bathtub

    Ultimately, it is best to have a professional unclog drains so the pipes do not get damaged. If you are unable to remove the clog yourself with hot water, a drain snake, or a plunger, avoid using other tactics as they could cause bigger issues.

    Be sure your plumber specializes in both traditional plumbing service as well as drain cleaning. You may need to have your pipes thoroughly cleaned to remove additional build-up that could cause your drains to stop working in the near future.

    A plumber will be able to use specialized tools to unclog safely without damaging your pipes. In some cases, portions of the piping may need to be removed or replaced if the clog is severe.

    A professional plumber may also try hydro jetting to unclog the pipes. This involves using a high-powered water pressure machine to create a strong stream of water that will run through your pipes to quickly remove any blockages. This also helps to clean out the entire plumbing system, so you wont deal with any clogs in the near future.

    In the mean-time, there are some other tips you can try to prevent your bathtub from clogging again. First, use drain covers in the shower or tub that will capture large items like clumps of hair or small pieces of plastic from going down the drain.

    Cleaning up your tub regularly can help to prevent build-up from soap residue, dirt, sand, and other clogging culprits. Try to rinse out the shower after use and deep clean it regularly.

    Different Bathtub Drain Stopper Types

    Everyone knows that bathtub drain plugs are used to keep water in a bathtub. However, they might be unaware that they have to consider some factors before choosing various types of bathtub drain stoppers.

    For instance, drains come in various sizes, and its vital that you choose a plug that matches the bathtub drain perfectly. Its also important you find the right plug to place beneath the bathtub tray because some models can be hard to clean.

    Fortunately, most retail stores stock bathtub drain plugs of various sizes so there is a high chance that you will find a plug that meets your needs. Here are the different styles of stoppers for bathroom drains.

    You May Like: 3 Compartment Sink Drain Parts

    Easy Step On How To Remove Push

    These models share the same design with toe touch variants. However, they do not have springs. Here are steps to remove push-pull drain stoppers.

  • Open the stopper and remove by twisting the knob in a counterclockwise fashion. You can use either your hands or two pairs of pliers for this task.
  • Unscrew the mounting post with counterclockwise movements. This action will help to remove the stopper from the drain fitting. Next, clean any mess on the drain opening with a small brush.
  • Clean the stopper with the brush and a household cleaner solution. Use a lemon and vinegar solution or chrome polish to give the stopper an extra shine.
  • Thread the mounting post of the stopper back into the bottom drain fitting. Reattach the knurled knob on top of the stopper.
  • Fix the mounting post to the bottom drain fitting. Return the knob to the surface of the stopper.
  • Check if the stopper is working correctly.
  • How To Fix Bathtub Drain Stopper

    EVERSO Pop Up Drain Stopper With Overflow Bathroom Basin Sink Drain ...

    you how to fix bathtub drain stopper

    SimpliQuick® Tub Fix by Watco, a name trusted by professionals, simply fits right on top of your existing drain with a universal fit for most tubs. Well show you the easiest way to remove your bathtub stopper and how to install your shiny new drain stopper with step-by-step instructional videos. Upgrade the look of your bathtub with everything you need from FixMyDrain.com.

    Read Also: Why Is My Floor Drain Backing Up

    RELATED ARTICLES

    Most Popular