S To Initiate The Self
The different steps are labeled C0 through C9 or so.
- C0 Slow spin mode
- C8 Drain pump and slow spin
- C9 Spinning Stops
If the test does not finish, and hangs up on one of the steps, that indicates which function is the problem. In my case, it stayed on C8 because the washer never drained. If you get the error code F32, this indicates a bad drain pump as well.
If you believe the pump is okay, but you just have a clog, check out this post on how to fix a clogged drain pump.
Cleaning The Drain Pump Filter/draining Residual Water On Your Maytag Front Load Washer
NOTE: Perform the following procedure occasionally or every 6 months.
If you would like to download or view product literature for your appliance, please visit our Manuals and Literature page.
Reasons Why Maytag Washer Not Draining Lets Fix It
We all know that Maytag washers are some of the most reliable washing machines on the market. However, if your Maytag washer not draining, get your hands dirty and follow our troubleshooting guide to fix it.
The Maytag washer is one of the most popular brands of washing machines around the country. With their long history of making quality appliances, its no wonder so many people choose Maytag washers. However, these machines will experience problems over time. One common problem with the Maytag washer is that it wont drain. This can be frustrating to people who want to get back to their everyday routine.
Below, we will discuss a few simple solutions that you can try out to fix the Maytag washer drain issue. One of these steps should resolve your problem with no further hassles.
Don’t Miss: How Deep Should French Drain Be
Clogged Drain Pump Filter
if you hear that the pump is running but water isnt going down, its likely that theres a clog in the pump filter. This can lead to a complete lack of water flow or a slow-down in the stream and can be fixed by taking out the pump filter and cleaning it.
Unplug the washer from the outlet, and carefully pull it away from the wall. If you can see or easily reach the filter, remove it. If not, unplug the washing machine and look at the back panel for a removable filter.
Unplug the machine and unplug the wall. Remove the access panel on the back of the machine and locate the drain pump. Unscrew the pump, remove the hose from the inlet side of the pump, and check if there is any debris in this hose. If you find any debris, clear it out and screw that hose back in.
Maytag Washing Machine Pump Parts
Order by 8:00 PM ET, this part ships TODAY!
Washing machine drain pump. The pump mounts directly to the motor with two clips. If the washer does not drain then the pump could be locked up or a small object may be clogging it. A small leak in front of the washer could be caused by a defective pump.
OEM Part – Manufacturer #WP3363394
Consider replacing the motor coupling while you have the washing machines cabinet off.
Don’t Miss: Drain Is Clogged In Shower
Check The Pump Housing
Now you should be able to see the drain pump, the internal drain hose, and the bottom of the washer tub. Its time to start hunting for that sock-clog. Start by looking in the drain pump housing, which is often translucent. You may even be able to see whatevers in there. Disconnect the drain hose, ready to catch any water with a towel. Then clamp the drain hose for now.
If something is caught in the drain pump, youll need to unhook the belt from the drain pulley underneath. Grasp the clogging item with your needle-nose pliers and twist the pulley to unwind the item from the drain assembly. Pull the clogging item out from the top of the pump, where the drain hose was connected.
Prop Up The Washer Front
The next step is interesting, you may not have heard of this one before. Lift up the front of your washing machine and place two paint cans underneath, one under each front foot. If youre not fixing a Maytag and your drain is behind the back panel, tip it the other direction and look up the steps to open that panel instead. You may need the help of a friend for this part.
Also Check: Drain Snake Won’t Make Turn
Inspect The Internal Drain Hose Tub
IF the clog isnt near the pump-side of the drain hose, it might be near the tub-side. Disconnect the other side of the internal drain hose, towel ready to catch any falling water. Then check inside both ends of the drain hose, and the aperture where the drain hose disconnected from. In one of these places, you should find the clogging small article of clothing.
Maytag Washing Machine Drain Pump
Order by 8:00 PM ET, this part ships TODAY!
Washing machine drain pump. The pump mounts directly to the motor with two clips. If the washer does not drain then the pump could be locked up or a small object may be clogging it. A small leak in front of the washer could be caused by a defective pump.
OEM Part – Manufacturer #WP3363394
Consider replacing the motor coupling while you have the washing machines cabinet off.
Don’t Miss: Home Depot 4 Inch Pvc Drain Pipe
Procedure To Fix A Bad Maytag Drain Pump
Replacing the pump is pretty easy, 3 screws and 2 hose clamps. Follow these steps to replace the drain pump.
First, unplug the washer.
Turn off both the hot and cold water supply.
Move the washer to a location where you can get at the back of it. Here I have tipped the unit up in order to see the pumps underneath. The pump on the left is the drain pump that we will be repacing .
If your washer is still full of water , then you will need to drain the water out. Tip the unit forward slightly so you can get under it . Then use a pliers or vise grips to remove the pipe clamp connected to the bottom of the tub and going to the pump, as shown below.
Slide the clamp down.
Pull the rubber hose off of the tub.
ATTENTION! water will start flooding out of the tub . Use a drain pan, or be positioned over a floor drain for this step!
Use a flat-head screwdriver to pry open the plastic cover that houses the electrical connection. There are 2 plastic tabs, one on each side. It doesnt matter if you break these off, since you will be replacing it anyway.
Press the tab on the electrical connector while pulling it out to disconnect it.
Next, remove the three 5/16 socket-head screws that hold the pump in place.
Here is a view of the old pump and new drain pump side by side for comparison.
The new pump comes with the short rubber hose. Take the old hose clamp off of the old one, and slip it onto the new one.
Do the same for the upper drain hose.
Youre all set!
How To Replace The Drain Pump On A Maytag Neptune Washer
If you’re getting the “ND” — no drain — error code on your Maytag Neptune washer, the first thing to check is the drain hose behind the machine it could be blocked by lint or even an old sock. If it the hose is clear, the problem probably has something to do with the drain pump inside the machine housing. To access it, you need to remove the cover from the back of the machine. The pump can also get clogged, but you may discover that the impellers are broken. If so, it’s a straightforward task to replace the pump.
1.
Unplug the washing machine and shut off the water supply valves. Pull the machine far enough away from the wall so there’s room for you to work comfortably behind it. You may need to unhook the water hoses — if so, use adjustable pliers to loosen the connectors.
2.
Remove the back panel by unscrewing the screws that hold it with a Phillips screwdriver. You should find two screws — one on either side of the panel. After removing the screws, slide the panel up to remove it.
3.
Locate the drain pump on the bottom of the machine to the left. It has two drain hoses connected to it with pipe clamps. Pull off the electrical connector.
4.
Unscrew the clamp holding the hose that leads from the washer tub to the pump. Pull off the hose and direct it into a 2-gallon or larger bucket to catch water that hasn’t drained. Once all the water has drained out, remove the second hose in the same way.
References
Read Also: Hair Trap For Shower Drain
Pull Away From The Wall
With your supplies ready, its time to prep the washing machine. Start by pulling your washer away from the wall. You will likely need to access the back to turn off the water among other things. Many models of washer have the drain pump accessible from the back, though well be accessing the Maytag drain pump through the front panel. If necessary, ask a friend to help you move the washer forward. Consider using a towel or cardboard to prevent scratching the floor.