Why Trust Spencers Tv & Appliance
Since 1973, Spencers TV & Appliance has grown to 10 locations throughout the Phoenix Metropolitan Area. The secret to our longevity is simple: personal service. Customer satisfaction have always been the focus of our business, and throughout the years, we have been able to work hard with our suppliers to bring you the best prices. After all, getting customers the best price and personal attention is how we compete with big-box stores, day in and day out.
Not only do we offer top-rated appliances, name-brand electronics, and the best mattresses on the market but we also provide water treatment solutions and perform kitchen design services. Stop by your nearest Spencers and see what youre missing!
Clogged Or Defective Drain Pump
If the washer is spinning but the clothes are still wet at the end of the cycle the draining issue could be caused by a faulty drain pump or a drain pump blockage.
Most washers need to be disassembled to check the drain pump for the issues. Depending on the type of washer, you may need to put the washer on its back to access the pump underneath the tub or remove the washers front panel to locate the drain pump beneath the drum. Depending on the washer, removing the rear access panel may also provide access to the drain pump.
Washer Not Draining Here’s What You Can Do
You need reliable appliances in order to run your household. You dont have time to squeeze out soaking wet clothes because your washer didnt drain especially if you planned to wear those items later on. A washer not draining is more than an annoyance, its a waste of water and energy. It can also cause you to run the dryer longer because the washer was unable to remove most of the water.
Dont live with a washer not draining. Here are a few causes of this problem and potential solutions to get it running again.
Don’t Miss: Kitchen Sink Drains Slow And Gurgles
Why Is My Washing Machine Leaking
Loose hose connections are the most common cause of washer leaks. If you suspect your leak is coming from the back of the washer, move it away from the wall a few inches and hand-tighten all hose connections between the appliance and the supply pipes.The location of the leak can also give you a hint. For top-load washers, a leak from the top could be due to oversudsing or overloading , whereas a leak from the bottom could suggest an issue with the water pump. For front-load washing machines, a front leak could be caused by a damaged or dirty door seal, but a bottom leak is more likely to be caused by a worn drum seal.
Does Resetting Fix All These Issues Ge Stackable Washer Dryer Troubleshooting Tips
Resetting cannot solve every problem you encounter. You have to experiment with different solutions until you find one that works. For instance:
1). Make sure the faucets are connected and turned on fully. Washers require a specific pressure.
2). The machine cannot start a cycle until the lid is closed tightly. The appliance wont run if it has a faulty door lock and switches assembly. But before you blame your problems on a defective assembly, identify and remove dirt and debris from the door gasket.
3). Dont overload the internal compartment. If the machine wont agitate, you can either reduce or redistribute the load.
4). Clean blockages, drains, and filters.
5). Some machines will stop in the middle of a cycle because they have a problem. But others will do so because of an automatic self-check system. Therefore, you shouldnt panic.
Recommended Reading: Baking Soda For Drain Cleaning
Follow These Steps To Check The Drain Pump:
If the steps above fail to diagnose and fix the issue, you should check that the drain pump isnt defective by performing a continuity test with a multimeter. Note that this test is for electric drain pumps. If your washer has a direct drive pump that relies on the washer motor, you need to check that the motor is working properly.
How To Replace The Pump
Buy a new one to match.
- You can find a new pump by searching for your washing machines brand and model number online.
- Pro tip: Model numbers are usually stamped on a small metal plate located under the tub lid or on the top, side or back of the machine. Copy down all the plate information and use it to access online parts suppliers, or take it along to the parts distributor.
Family Handyman
You May Like: Draining The Knee Of Fluid
Check Your Machines Inner Workings
If the hose drains when placed in the bucket, its time to check the machines inner workings for problems. This includes examining the drain pump, the lid switch, the belts and the water level control .
The drain pump is likely behind a panel that can be removed with a screwdriver. After you remove the drain pump, examine it for debris or obstructions and make sure the moving parts move freely. Sometimes simply cleaning the pump will do the trick. If nothing appears to be wrong with the pump, check to make sure all belts are in place and intact.
Find the lid switch and press it down while holding the lid open. The switch should click into place. If it doesnt, or if it seems loose, it may need replacing. Continue to check other parts of your machine. You may also find it helpful to look at the user manual.
The manual may have additional troubleshooting tips specific to your machine. Top load washers and front load washers have very different configurations, for example. If you dont feel comfortable messing with your machines insides, you might also call a washer repair technician at this point.
Ge Stackable Washer Dryer Wont Start
You have a power problem. Check everything, not just the power cord, fuses, and breakers but the control board. Are you using an extension cord? Is the circuit large enough to accommodate the appliance?
Do you trust the wall outlet? If the washer dryer has a reputation for producing a humming sound, check and possibly replace the drive motor.
Don’t Miss: Hair Trap For Shower Drain
Ge Stackable Washer Dryer Not Locking
The door lock is corroded or damaged. Either way, the best option is to replace it. You can confirm your suspicions by testing the door lock switch for continuity.
If the door lock is fine, check the control board. You can try resetting the machine. Some glitchy control boards will respond to resetting.
Shop The Best Washers
Discover the best washers on the market with us!
- The machine is overloading your electrical system. An inefficient washer could flip a breaker or trigger an emergency electrical shut-off switch. This could be an appliance issue or a wiring issue.
- The drain hose is clogged. This hose carries water from your washer into your septic tank or sewer system. If the hose is clogged, water might not drain or it might take much longer than expected.
- The lid switch is broken. This secures the washer drawer so it can run without splashing water into your house. Check under the lid door to see if it is functioning.
- The belt is broken. This powers the engine and makes your machine work.
- The pump is broken. Your system isnt able to push water out of the tub, which means it stays in there until it can drain slowly on its own.
Many of these issues arise because of the age of your appliance. While some problems occur because of use others are caused by the breakdown of parts over time. Just the belts in your car, washer belts arent made to last forever and need to be replaced as the appliances get older.
Also Check: Drain Pump For Kenmore Elite Washer
Explore Top Washer Models On Todays Market
There are multiple washer designs and styles to choose from if you are ready to replace your old appliance. You can choose from basic washers that fall in affordable price ranges or more advanced styles that come with extra technology features and WiFi connectivity. Here are a few top washer brands to consider as you start your search.
Why Wont My Washing Machine Drain
A few different factors could be at work if your washing machine fails to drain at the end of a wash cycle:
- Lid switch: The lid switch confirms that the lid is closed, allowing top-load washers to proceed with various stages of the cycle: fill, wash, drain, spin. If this switch malfunctions, you may be left with a drum full of water. Press this switch down with your finger and listen for a click or see if the ‘lid closed’ light turns on . You can either replace the switch yourself or have a qualified technician do it.
- Pump: The pump actively removes water from your machine at the end of a cycle. If it gets blocked, draining will be prevented. To reach and inspect the pump, remove the panel , detach it, and remove the screen for a thorough rinsing. Make sure moving parts can move freely and are not broken or missing.
- Drain hose: Your drain hose could have a kink or blockage that prevents drainage. Turn off the power to the washer, disconnect the hose , and inspect it for obstructions. You may be able to clear any blockages by taking it outside and blasting it with a spray from your garden hose.
- Drain: It could be that the drain itselfnot the washeris preventing drainage. Use a plumber’s snake to clear the blockage, and remember to carefully inspect your clothing for small items before you load your washing machine. These items can get caught in many places, including the drain, causing serious draining difficulties.
You May Like: Fiberglass Shower Drain Removal Tool
Clean The Drain Pump Filter
Almost all GE washers have a drain pump filter. However, over time, the filter gets clogged due to debris build-up and needs to be cleaned.
If you havent cleaned your GE washer drain pump filter for quite a long time, there is a high chance its clogged and is the leading cause of your washer not draining the water.
Ge Stackable Washer Dryer Not Spinning
A faulty lid switch assembly can also prevent spinning. Although, the most obvious culprit is the drive belt. If the drive belt wears out or breaks, the washer stopped spinning.
Other notable causes included faulty motor coupling and a burned-out control board. Most of these problems require technical support. You cant solve them by resetting the device. But that shouldnt stop you from trying.
For all you know, the washer stopped spinning because of a glitchy control board. You can solve glitches with a reset.
You May Like: 50 Ft Drain Snake Home Depot
Clogged Drain Pump Filter
if your pump is running but water is not coming out of the machine, you have a clog in the filter. The easiest way to fix this issue is to remove the filter and spray it down with cold water. Once its thoroughly cleaned, install it back into the machine, plug it in, and turn it on.
If you suspect theres a problem with the washer, try accessing the pump filter. To access the filter, remove the machine from the wall. Then, take apart the back panel to locate the drain pump.
Turn off the water supply and remove the access panel at the bottom of your washing machine. Locate the drain pump, detach the hose from the inlet side, inspect it for debris, clear away any you find, and reattach it. Put back together and switch on the water supply. If you still see water draining into the drum, check air-drainage pressure at your external drain location.
Why Your Ge Washer Isnt Draining Here Are 6 Possible Causes And Solutions
Heres the thing:
The draining function is important to the wash cycle because it helps maintain a steady flow of bubbly and fresh water when needed.
Comparatively:
Just like a GE dryer that isnt heating, a washer that refuses to drain is quite frustrating.
Also:
A brand-new washer is less likely to develop this fault, but a fairly or well-used washer is most prone to it.
Now:
Your GE washer is unusable if it cannot drain.
You probably clicked on this guide because youre facing this problem and need to learn how to fix it.
Well:
Youve come to the right place.
Here is a short list of faults that could lead to a drainage failure in your GE washer.
Recommended Reading: Drain Pan For Ac Unit
Remove And Check The Drain Hose
Behind the washer, you will find the drain hose. Its connected to the appliance at one end while the other goes into a drain pipe that leads out of your house. First, verify that the hose isnt pinched or kinked anywhere, then pull the hose out of the pipe and inspect it for clogs.
If you find any debris, you should most definitely remove it. Then, set everything back up, turn the water and electricity back on and try starting your washer again. If the clog was the problem, it should now drain. If it still doesnt drain, or if you didnt find a clog, then make sure the power and water supply are shut off again before proceeding to the next step.
Remove Any Kinks In The Hose
GEs washer may have a clog in the hose, filter, or pump, which can cause the washing machine not to drain.
Troubleshooting steps:
- To fix this, turn off the washer and unplug it from the power outlet.
- Then, remove any kinks in the hose and double-check that its connected to your GE washer properly.
- If there are no kinks, check for any holes at the bottom of the washer and open them up to see if water comes out.
- If this does not work, turn off the water coming into your house and clear any debris from around your homes supply valve or in your yard.
- Does the issue still persist? Then, there may be an issue with your drain pump. In this case, you will need to consult with a GE service center to provide you with assistance.
Recommended Reading: How To Fix Basement Drain Backing Up
Reasons Why Ge Washer Not Spinning
GE washers are well-known for their high quality and durability. However, with age and continuous use, even the best washers will need repair at some point in time.
While this may be unnerving for some people, it is very easy to repair a GE washing machine with a little patience and know-how. With this GE washer repair guide, you can fix the GE washer not spinning issue and running in no time.
The spin cycle is the most important part of any washing machine. If done correctly, it will remove almost all the water from your clothes, leaving them fresh and dry without weighing you down with heavy material. If your washer doesnt seem to be able to get the clothes clean at all, or if its making strange noises or vibrating a lot, then something will need repair.
You may be able to figure out what the problem is and fix it yourself. But if you cant or if the machine is not working at all, you will probably need to call a technician. We are here to help you troubleshoot and find out why your washing machine isnt working properly.
How Did My Drain Pump Get Blocked
Small things, like a piece of clothing, can get into the drain pump. Debris can also cause a blockage over time. This prevents your drain pump from functioning and that results in the washer not draining.
That also prevents the washer from running and it just hums.
Read: Why Washing Machine Leaves Lint On Clothes?
Don’t Miss: Perimeter Drain Vs French Drain
Ge Stackable Washer Dryer Keeps Stopping
GE stackable washer dryer keeps stopping because of a bad power supply. Another problem, such as a blocked vent. If lint blocks the vent, preventing the air from circulating, the appliance will shut down because the temperature is too high.
These devices have thermal overload switches that respond to overheating. But blocked vents have a simple solution. The same cannot be said for a defective door lock.
It will cause the washer to stop in the middle of a cycle. A faulty door lock can prevent the machine from running in the first place. The main control board is even more challenging because you must open the appliance to reach it.
You can fix some control boards by resetting the washer. But others are damaged beyond repair. Your only option is to replace them.
Check The Water Level Control Knob
GE washers operate with water level control knobs that have a range of settings. These knobs regulate the amount of water going into the washing load.
First, check the water level control knob and make sure it is not set to a position that will cause the machine to overflow. If it is at its highest setting, turn it down.
If the water level control knob is at its lowest position and you are still having this problem, then, it means your GE washer may be clogged with lint from too many towels or other large items being washed.
You can clean out any lint by running your hand around inside of the washer or using a long thin object like a coat hanger to poke out any lint thats clogging up your machine.
Read Also: How To Unclog Bath Tub Drain