Tuesday, December 5, 2023
HomeFactsGe Washer Drain And Spin Cycle Not Working

Ge Washer Drain And Spin Cycle Not Working

Check The Door Latch Switch

GE washing machine won’t spin or drain

The door latch on the GE washing machine is designed to prevent the door from opening during the wash cycle.

The washer safety system will continue operating if the door is closed correctly. When the door is closed, a feedback switch sends a signal to the washer control board. If this switch is faulty, your GE washer wont operate and drain the water, no matter if the door is closed.

The door latch switch is located beneath the control board on GE washing. So if your washer is under warranty, do not try to test it yourself, as it will void its warranty.

Even if your washer warranty period is over, Id recommend seeking a professional help to test or replace the door latch switch on your GE washer.

Clogged Or Defective Drain Pump

If the washer is spinning but the clothes are still wet at the end of the cycle the draining issue could be caused by a faulty drain pump or a drain pump blockage.

Most washers need to be disassembled to check the drain pump for the issues. Depending on the type of washer, you may need to put the washer on its back to access the pump underneath the tub or remove the washers front panel to locate the drain pump beneath the drum. Depending on the washer, removing the rear access panel may also provide access to the drain pump.

Inspect The Door Latch

The next step is to ensure the door latch is working correctly, and if not, replace it. Depending on your specific GE washer model, it will either have a mechanical door latch or an electric one.

Heres how to inspect the door latch:

  • If you have a mechanical door latch, check if the washer door closes properly and the latch clicks into place. If not, it will need to be replaced. If the door does close correctly, move on to step 5.
  • If you have an electric door latch, turn the power off to your washer, locate the door latch and check it with a multimeter for continuity. If the switch has continuity, its working correctly, and you can proceed to step 5.
  • If you do replace the door latch, turn your washer back on and check if the problem has been solved. If not, proceed to step 5.
  • Read Also: Can You Use Drano In Shower Drain

    Ge Washer Wont Complete The Spin Cycle

    If your GE washer wont complete the spin cycle, there are several possible causes. The most common cause is a problem with the washing machines lid switch.

    If the lid switch is defective, it may not signal the washing machine to stop spinning when the lid is opened. Other possible causes include a faulty door lock switch, a problem with the washing machines drive belt, or a problem with the washing machines timer.

    Ge Washer Wont Spin With A Full Load: Causes / How To Fix

    My GE washing machine doesn

    A washer overloaded with thick fabrics like towels and rugs will not spin. If there are too many clothing articles in your washing machine, removing some of the items will help your washer to spin.

    However, a washing machine that is not overloaded but wont agitate signals a loose belt.

    While your machine is full, open the front panel of your washing machine. Carefully inspect the belt and the pulley. If the belt appears to be slipping, replace it as soon as possible.

    If you have experience working with washing machines, you can do this at home. But for the best results, talk to a GE professional.

    Also Check: 4 Inch Corrugated Drain Pipe Fittings

    Schedule Washing Machine Repair

    If these troubleshooting tips dont solve the problem, you could have a broken water pump or drive belt. These components require professional repair or replacement to get your machine working again.

    Washing machine repair is best left to the professionals. If your washing machine still wont drain, its time to for help. Our experienced technicians can efficiently and effectively restore your washing machine to good working order.


    Faulty Water Inlet Valve

    The role of the water inlet valve in your washing machine is to release the necessary amount of water into the washer drum after the sensing spins have determined the load amount.

    However, suppose the water inlet valve is clogged. In that case, whether it be mineral buildup, gunk, or simply dirt that accumulated over the years, the water wont be able to pass through .

    It is also possible that the water inlet valve is corroded or damaged in some other way hence your GE washer ends up stuck on sensing.

    Read Also: Sewer Smell In Shower Drain

    Ge Washer Wont Complete Spin Cycle: Causes / How To Fix

    A failing lid switch assembly or a damaged door lock will cause your washing machine to stop mid-cycle.

    To determine which of these parts are responsible, test them with a multimeter. Replace the pieces that show a lack of continuity.

    Consult your washing machines manual for repair instructions. You must get the correct replacement parts that match your GE washers make and model for a successful at-home fix.

    Otherwise, get in touch with a trained professional who will repair your machine as soon as possible.

    Verify The Spin Cycle Is Set To Extended Not Standard Or Quick

    GE Front Load Washer Won’t Drain or Spin – Ideas to Troubleshoot & Fix

    If it is not, you should make the necessary changes. The spin cycle has an effect on the efficiency with which your washer removes water and dirt from your clothes.

    A longer spin cycle extracts more water and dirt from the system. As a result, your clothes will be cleaner. A shorter spin cycle, on the other hand, removes less water and dirt. This softens and fluffs the clothes, but may impart an odor.

    If you use a fabric softener or an odor-fighting powder, you must use more of it or the clothes will retain their odor. Most people use the Standard spin cycle by default.

    Also Check: Musty Smelling Drains In Bathroom

    Dirty Coin Trap Or Pump Filter

    Many washers have a coin trap or pump filter that screens out debris before water is drained, preventing it from clogging the drain pump. If this trap or filter isnt cleaned periodically, it can become clogged, resulting in a washing machine not draining completely.

    Refer to your user manual to determine the location of your washers coin trap or pump filter. Most are located behind a small door on the front right corner of the machine. Open the door, and twist the filter to remove it. Dispose of any debris, rinse the filter, and wipe down the filter housing before replacing it and closing the door.

    Examine The Water Pump

    If your washing machine does not spin but continues to agitate, there is a good chance that the water pump is malfunctioning. The pump is responsible for extracting water from the drum and redistributing it throughout the wash.

    The washing machine will not begin spinning until all of the water in the drum has been drained.

    Pumps become clogged from time to time and frequently develop problems as they age.

    If your washing machine makes an unusual noise or drains slowly, the problem may be with the pump. Unplug it and inspect it for blockages, such as lint or fabric softener sheets. If no visible signs of damage or clogging exist, it is necessary to replace the pump.

    Read Also: Which Apps Drain My Battery

    Install A New Water Inlet Valve

    If the water inlet valve is clogged, corroded, or damaged in any other way, it is highly probable that this is the leading cause of the sensing mode issue.

    You should be able to locate the water inlet valve inside the washing machine. Once you open up the top part, you will find it close to the back side of the washer.

    You will also notice that the valve is secured with screws while multiple wires and hoses are connected. Slowly unscrew the valve and disconnect it from all wires and hoses, ensuring not to damage any of these elements in the process.

    Since installing the water inlet valve can be rather complicated, you may want to leave this task to a licensed expert who can inspect other essential elements in the washer.

    Board Of Motor Control

    My Ge Washer Won T Drain or Spin  DerivBinary.com

    The motor is powered by the motor control board. If the motor control board is malfunctioning, the washer may not operate properly or at all.

    To begin, visually inspect the control board for burned-out components.

    To determine if the motor control board is defective, verify that it is powering the motor. If the control board is powered but is not powering the motor, it should be replaced.

    Recommended Reading: Well Draining Potting Soil For Indoor Plants

    Unbalanced Load Or Overfilled Washer

    If the washer is unbalanced or overfilled, it may struggle to spin and cause the clothes to still be wet after the spin cycle. Removing some items from the washer or balancing the load in the tub should resolve this issue. Make sure you dont overfill the washer and that the load is balanced to avoid the issue from recurring.

    Ge Washer Wont Do Final Spin: Causes / How To Fix

    A washer that wont do its final spin is a sure sign of a damaged timer. The machine is not receiving the timers signal to start the last cycle, so it never does.

    There are no at-home fixes for this type of problem.

    Homeowners should contact a GE technician immediately to service the machine and make repairs. Ignoring a broken timer will permanently damage your washing machine over time.

    Also Check: How To Use Thrift Drain Cleaner

    What Causes A Washing Machine To Not Spin Or Drain

    Opening the washing machine lid or door after the end of the wash cycle and discovering your clothes are still submerged underwater can really dampen your spirits. Before you invest in a vintage hand-cranked laundry wringer to squeeze out that water, you should troubleshoot the likely causes of the washer failing to drain or spin . The solution to the problem can be quite simple, and the appliance replacement part you need can be relatively inexpensive and easy to install.

    The reasons a washer will fail to drain, or spin, will differ depending on whether you own a top-load model or a front-load model. Lets examine how each washer type handles these two cycles

    The Washing Machine Is Too Full

    How To Repair – GE Stackable Washer Dryer Combo not Spinning or Draining

    When your washing machine is overstuffed, it may fill but not spin. Some washer models have automatic detectors to tell you if you’ve overfilled your washing machine, but many don’t. The machine generally won’t recognize the issue until the washer has filled with water. If that’s the case, unfortunately, your only solution is to remove some of the soggy clothes.

    Don’t Miss: How To Stop Hair From Clogging Shower Drain

    Check The Washer Timer

    If your GE washing machine is automatic or semi-automatic, its functions depend on the timer. The washer controller is programmed as per your set washing cycle instructions.

    If the timer on your GE washer is faulty, it might get stuck when shifting from wash to spin or from spin to spin.

    Testing and replacing the washing machine timer is not something Id recommend doing yourself, so always seek professional help.

    Blocked Drain Pump Filter

    To clean a blocked drain pump filter in your GE washing machine, do the following

    Step 1. Make sure your washing machines water and power supply is turned off in order to avoid water leakage and electrocution.

    Step 2. Use a flat-blade screwdriver to pry out the little panel at the lower front section of your washing machine. Pull out the drain channel under the panel.

    Step 3. Place a container under the drain channel to catch any water that is stuck in the washing machine.

    Step 4. To control the quantity of water being released, turn the knob inside the drain channel counterclockwise slowly and pull it out .

    Step 5. Once youve drained out all the water from your washing machine, take the drain pump filter to a sink and clean out any accumulated dirt or lint.

    Step 6. Once youve cleaned the filter properly, put it back in place and turn it clockwise to secure.

    Step 7. Flip the drain channel up and push the access panel back in place.

    Step 8. Turn on your washing machines water and power supply.

    Step 9. To ensure that everything is working properly, run a wash cycle.

    Recommended Reading: Fruit Fly Killer For Drains

    Clothes Still Wet After The Spin Cycle You Can Fix It

    If your clothes are still wet after the washer finishes its spin cycle, the water isnt draining as it should. Therefore, you need to check all the components that could be stopping the washer from draining correctly. Typically, this means checking the drain hose, drain pump, and any filters or coin traps that could be blocked. Other causes of clothes still being wet after the spin cycle include an unbalanced washer, using the wrong detergent, or a worn or loose drive belt.

    Heres how to diagnose and fix the issue.

    Ge Washer Makes A Clicking Noise And Wont Spin: Causes / How To Fix

    Ge model WBXE2070A0WW residential washers genuine parts

    A clicking washing machine is the result of a clogged water drain or damaged control panel.

    When the draining system is blocked, noises come from the water pump as the liquid struggles to get out. Clearing out the water drain can fix most noisy washing machines.

    However, if the clicking is coming from the GE washers control board, that means there is an electrical issue. In that case, switch out the control panel. Replacing the control panel is complicated and should only be done by a skilled handyman.

    Recommended Reading: Rough In For Toilet Drain

    Clothes Do Not Spin Dry In Washing Machine

    If your clothes remain dripping wet after your washers spin cycle, perform the following:

    1.Lift the lid during the spin cycle. If the tub is not spinning, you may have a damaged motor coupler. You can find affordable , but call an appliance repair person to replace this part.

    2.If the tub is spinning, recheck the load to make sure it is balanced. If you are certain the load is balanced but your clothes still come out dripping, you may need to have a damaged motor pulley, tub bearing, belt, or clutch replaced.

    3.Be sure the drain hose isnt kinked. Then check the tab on the lid that strikes the lid switch if its broken, the washer may stop during the drain cycle. Press and release the lid switch. If it doesnt click each time you do this, its probably broken. Remove the switch, test it, and replace it if needed.

    4.The water pump may be broken or clogged with a small article of clothing, or the controls may be broken call an appliance repair person.


    Ge Washer Wont Do Final Spin

    If your GE washer wont do a final spin, there are several potential causes.

    The most common cause of a GE washer not spinning is an imbalance in the load. If the clothes in the washer are not evenly distributed, they can become tangled around the agitator or build up on one side of the tub. This can cause the washer to become unbalanced and stop spinning.

    Another common cause of a GE washer not spinning is a problem with the lid switch. The lid switch is a safety feature that prevents the washer from spinning when the lid is open. If the lid switch is defective, it may prevent the washer from spinning even when the lid is closed.

    If your GE washer wont do a final spin, check to see if the clothes are evenly distributed in the tub. If not, redistribute them and try again. If that doesnt work, check the lid switch to see if it is defective. If so, replace it. With a little troubleshooting, you should be able to get your GE washer spinning again in no time.

    Recommended Reading: How Do Flat Roofs Drain

    Look For The Clog And Pull It Out

    The pump has a translucent housing, so you might even see the offending piece of clothing wrapped up in the pump.

    • Loosen the clamp that holds the hose to the bottom of the tub and remove the hose.
    • Pro tip: Have a bucket and sponge handy. Any water thats left in the machine will run out.
  • Remove the belt from the pulley on the bottom side of the washing machine water pump, and if the clog is visible, pull it out.
  • Twist the pulley to unwind the fabric as you pull it out.
  • Pro tip: If you dont see the clog in the pump or in the washing machine drain hose near the pump, then it could be stuck in the outlet where the hose connects to the bottom of the tub.
  • Family Handyman

    Reasons Why Ge Washer Not Spinning

    GE Washer not spinning or draining 2 MINUTE FIX!!!

    GE washers are well-known for their high quality and durability. However, with age and continuous use, even the best washers will need repair at some point in time.

    While this may be unnerving for some people, it is very easy to repair a GE washing machine with a little patience and know-how. With this GE washer repair guide, you can fix the GE washer not spinning issue and running in no time.

    The spin cycle is the most important part of any washing machine. If done correctly, it will remove almost all the water from your clothes, leaving them fresh and dry without weighing you down with heavy material. If your washer doesnt seem to be able to get the clothes clean at all, or if its making strange noises or vibrating a lot, then something will need repair.

    You may be able to figure out what the problem is and fix it yourself. But if you cant or if the machine is not working at all, you will probably need to call a technician. We are here to help you troubleshoot and find out why your washing machine isnt working properly.

    Don’t Miss: Drain Electric Hot Water Heater


    Most Popular