Ge Washer Makes A Clicking Noise And Wont Spin: Causes / How To Fix
A clicking washing machine is the result of a clogged water drain or damaged control panel.
When the draining system is blocked, noises come from the water pump as the liquid struggles to get out. Clearing out the water drain can fix most noisy washing machines.
However, if the clicking is coming from the GE washers control board, that means there is an electrical issue. In that case, switch out the control panel. Replacing the control panel is complicated and should only be done by a skilled handyman.
Connect With An Appliance Repair Tech
No in-home service calls. No appointments.
Mechanical failures in drain pumps include:
- A foreign object is clogging the centrifugal pumps impeller.
- As a result, the impeller inside is broken or otherwise damaged.
Electrical failures, on the other hand, include:
- A short-circuit inside the pump.
- Loose or damaged pump wiring.
How to fix it: The most practical solution to a failed drain pump is a complete replacement. However, in some cases, you might be able to remove an item clogging the inside of the pump.
However, that clog might have also caused the pump to overheat or damage itself as it tries to force its impeller to turn.
So, if you have to replace it, you can find the drain pump underneath the sump. The drain pump will be at the lowest part, no matter your GE washer model.
Read:Why Washing Machine Makes Loud Noise When Draining?
Check The Door Latch Switch
The door latch on the GE washing machine is designed to prevent the door from opening during the wash cycle.
The washer safety system will continue operating if the door is closed correctly. When the door is closed, a feedback switch sends a signal to the washer control board. If this switch is faulty, your GE washer wont operate and drain the water, no matter if the door is closed.
The door latch switch is located beneath the control board on GE washing. So if your washer is under warranty, do not try to test it yourself, as it will void its warranty.
Even if your washer warranty period is over, Id recommend seeking a professional help to test or replace the door latch switch on your GE washer.
Don’t Miss: Installing Drain Tile In Basement
Ge Washer Dryer Combo Not Draining
If your GE washer dryer combo is not draining, there are a few things you can do to troubleshoot and fix the problem.
First, check to make sure that the drain hose is not kinked or clogged. If it is, try straightening it out or clearing the obstruction.
Next, check the drain pump filter for any foreign objects that may be blocking it. If you find anything, remove it and clean the filter.
Finally, check the drain pump itself for any debris or obstructions. If you find anything, remove it and clean the pump.
If your GE washer dryer combo still will not drain after following these steps, then you may need to call a technician for assistance.
Door Lock Motor And Switch Assembly
If your GE washer is not draining properly, it could be due to a problem with the door lock motor and switch assembly.
This is a relatively easy problem to fix, and you should be able to do it yourself in just a few minutes.
Why does it fail?
The most common reason for the door lock motor and switch assembly to fail is because of a power surge. A power surge can cause the door lock motor and switch assembly to become damaged or even burn out.
Another reason for the door lock motor and switch assembly to fail is because of a faulty wiring connection. If the wiring connections are not correct, it can cause the door lock motor and switch assembly to fail.
Finally, if the door lock motor and switch assembly become wet, it can also cause the door lock motor and switch assembly to fail.
How to fix it?
First, unplug the washer from the power outlet. Then, remove the screws that secure the door lock motor and switch assembly to the washer. Carefully pull out the assembly, being careful not to damage any of the wires.
Once you have removed the door lock motor and switch assembly, check to see if the problem is with the door lock itself or with the switch. If it is with the door lock, you will need to replace it. If it is with the switch, you can either replace it or try to clean it and see if that solves the problem.
Finally, if the door lock motor and switch assembly is wet, you will need to dry it off before you can use it again.
You May Like: What Do Plumbers Use To Unclog Drains
Clothes Do Not Spin Dry In Washing Machine
If your clothes remain dripping wet after your washers spin cycle, perform the following:
1.Lift the lid during the spin cycle. If the tub is not spinning, you may have a damaged motor coupler. You can find affordable , but call an appliance repair person to replace this part.
2.If the tub is spinning, recheck the load to make sure it is balanced. If you are certain the load is balanced but your clothes still come out dripping, you may need to have a damaged motor pulley, tub bearing, belt, or clutch replaced.
3.Be sure the drain hose isnt kinked. Then check the tab on the lid that strikes the lid switch if its broken, the washer may stop during the drain cycle. Press and release the lid switch. If it doesnt click each time you do this, its probably broken. Remove the switch, test it, and replace it if needed.
4.The water pump may be broken or clogged with a small article of clothing, or the controls may be broken call an appliance repair person.
NEXT SEE
Blocked Drain Pump Filter
To clean a blocked drain pump filter in your GE washing machine, do the following
Step 1. Make sure your washing machines water and power supply is turned off in order to avoid water leakage and electrocution.
Step 2. Use a flat-blade screwdriver to pry out the little panel at the lower front section of your washing machine. Pull out the drain channel under the panel.
Step 3. Place a container under the drain channel to catch any water that is stuck in the washing machine.
Step 4. To control the quantity of water being released, turn the knob inside the drain channel counterclockwise slowly and pull it out .
Step 5. Once youve drained out all the water from your washing machine, take the drain pump filter to a sink and clean out any accumulated dirt or lint.
Step 6. Once youve cleaned the filter properly, put it back in place and turn it clockwise to secure.
Step 7. Flip the drain channel up and push the access panel back in place.
Step 8. Turn on your washing machines water and power supply.
Step 9. To ensure that everything is working properly, run a wash cycle.
Recommended Reading: Fruit Fly Killer For Drains
Read Also: Installing Drain Tile Around Foundation
How To Drain Water Manually
If your GE washer does not drain the remaining water in the wash tub you may need to drain it manually. Front load vs top load washers have a drain pump filter that can be accessed to drain the water without causing leaks.
Follow these steps to manually drain water from a GE washer:
- Use a screwdriver or small coin to open the pump filter access door on the bottom right corner of the washer. Pull down the drain channel.
- Position a shallow dish under the drain channel to contain draining water. Protect the floor by placing a towel beneath the dish.
- Slowly turn the filter counterclockwise before removing it completely. At least a quart of water may be released. If the dish fills with water, replace the filter and dispose of the water before resuming draining.
- When all the water is drained, slide the filter back in its housing and turn clockwise to lock in place.
- Lift up the drain channel and close the filter access door.
Ensure That The Water Is The Proper Temperature
The temperature of the water in the majority of washing machines is controlled by an automated thermostat. However, you should verify this with the manual.
Almost certainly, you will need to adjust the temperature of the water slightly.
For instance, if your water is too hot, turn it down a few degrees. If the temperature is too low, increase it by a few degrees.
When adding the detergent, the washing machine must reach a temperature of at least 40°C . If the water is too cold, it will not function properly. On the other hand, using excessively hot water can cause damage to your washing machine.
To determine the proper temperature, refer to the instructions on the packaging of your washing machine.
Read Also: Hair Trap For Shower Drain
Reasons Why Ge Washer Not Spinning
GE washers are well-known for their high quality and durability. However, with age and continuous use, even the best washers will need repair at some point in time.
While this may be unnerving for some people, it is very easy to repair a GE washing machine with a little patience and know-how. With this GE washer repair guide, you can fix the GE washer not spinning issue and running in no time.
The spin cycle is the most important part of any washing machine. If done correctly, it will remove almost all the water from your clothes, leaving them fresh and dry without weighing you down with heavy material. If your washer doesnt seem to be able to get the clothes clean at all, or if its making strange noises or vibrating a lot, then something will need repair.
You may be able to figure out what the problem is and fix it yourself. But if you cant or if the machine is not working at all, you will probably need to call a technician. We are here to help you troubleshoot and find out why your washing machine isnt working properly.
Master Reset To Factory Settings
If the machine does not spin, you have two options: reload it and restart it, or drain it and perform a master reset.
Unplug the machine and open the door to drain it. Once it has drained sufficiently, close the door and reconnect the plug.
Unplug the washer and open and close the door six times in 12 seconds to perform a master reset. Each washer will have its own unique reset mechanism.
If none of the fixes listed above resolves your issue, its time to consult a professional.
Recommended Reading: Pool Deck Drain Home Depot
Check The Fabric Type
If youre using a powder-type detergent and adding the recommended amount, but your washing machine still wont spin, check the fabric type.
Different fabrics require varying amounts of detergent to be cleaned properly.
For instance, synthetic fabrics such as polyester and nylon require more detergent than natural fibers such as cotton or wool.
If youre unsure of the fabric youre using, bring some of your laundry to a laundromat or consult with friends or relatives who own sewing machines.
Tips To Prevent Draining Problems
Many draining problems can be avoided with proper maintenance, use, and care.
Heres how to prevent issues from a GE washer not draining:
- Check clothing pockets: When loading your machine, always check clothing pockets and remove any foreign objects that can cause a blockage.
- Clean washer regularly: Clean a washing machine on a monthly basis with a commercial tub cleaner or baking soda and vinegar. Wipe down the gasket on front load washers as well. This can prevent an accumulation of dirt and debris that can cause clogs.
- Empty coin trap or pump filter: When you clean the washer, empty the pump filter as well to remove any dirt or blockages.
- Always use HE detergent for HE machines: Using regular detergent in an HE washer creates excess suds, leaving behind a residue that can cause clogs.
If draining problems continue, it may be time to call in the GE washing machine repair experts. The team at A-Tech Appliance Parts & Service can handle any washer issue!
What can we help you with?
repair & maintenance tips
You May Like: French Drain Around House Foundation
Inspect The Drive Motor
The final step is to inspect, and if necessary, replace the drive motor. The drive motor helps the drum to spin during a wash cycle so if it becomes faulty your washer will not be able to spin.
Heres how to inspect the drive motor:
Check The Pump Replace It If It Is Faulty
If your GE washer is not draining, then you need to ensure that the pump is working. If it is not, then it could be clogged or faulty.
Here are the steps for troubleshooting:
- First, check the pump. You can do this by turning off the power and removing any clothing from the washer to get access to it.
- Take a flashlight and shine it onto the pump.
- If you see water or soap bubbles coming out of it, then you know that there is a blockage in it, and you need to clean it out with a plunger or long thin rod, like a broom handle, until all of the bubbles are gone.
- Once the cleaner has been poured back in and you have started up again, your washer should start draining properly again.
- If you are still not sure what is wrong with the pump, give a call to the GE service center.
Recommended Reading: Top Load Washer Won’t Drain
Inspect The Motor Control Board
The next step is to inspect, and if necessary, replace the motor control board. When the motor control board stops working, the power supply to your GE washer is interrupted and your washer wont be able to spin.
Heres how to inspect the motor control board:
Potential Wrong Cycle Setting
Your GE washer could also fail to spin your clothes dry because of a wrong cycle. For instance, washing bulky clothes with a hand-wash or delicate washer setting wont do the clothes any good.
They are likely to drip wet at the end of the wash as the spin cycle is too weak for them. Bulk clothes may also drip wet if you use a slow spin on them.
Ensure you pick the right wash/spin setting according to the type of clothes you are washing.
Sometimes, it helps to go for a faster spin, especially when cleaning heavier, thicker, and bulkier laundry. Ensure your washing machine doesnt spin too fast to damage the clothes.
Don’t Miss: Drill Drain Hole In Ceramic Pot
Check For Loose Power Connection
Sometimes, a loose power connection causes the GE washer not to spin completely, and you may end up with dripping clothes. Here are two potential culprits:
- The power cord is not well plugged in correctly
If the power cord is not well plugged into the power socket, the washer may not have enough power to spin the clothes dry.
Check the power cord to ensure it completely plugs into the power source if thats not the case.
- Use of an extension
Its never a good idea to plug your GE washer into an extension cord. Why?
Most extension cords fail to transmit the amount of power the washer needs to run correctly. So, the washer may not complete the spin cycle, leaving the clothes dripping at the end of the process.
Sometimes, the washer overheats and stops mid-cycle, which means your clothes are likely to be wet at the end of the wash.
Instead of plugging into an extension cord, plug into the wall socket. If you must use an extension cord, ensure it is powerful enough to power the washing machine fully.
Ge Washer Wont Spin With A Full Load: Causes / How To Fix
A washer overloaded with thick fabrics like towels and rugs will not spin. If there are too many clothing articles in your washing machine, removing some of the items will help your washer to spin.
However, a washing machine that is not overloaded but wont agitate signals a loose belt.
While your machine is full, open the front panel of your washing machine. Carefully inspect the belt and the pulley. If the belt appears to be slipping, replace it as soon as possible.
If you have experience working with washing machines, you can do this at home. But for the best results, talk to a GE professional.
Also Check: 4 Inch Corrugated Drain Pipe Fittings
Read Also: How To Make Sinuses Drain
Clogged Drain Pump Filter
if your pump is running but water is not coming out of the machine, you have a clog in the filter. The easiest way to fix this issue is to remove the filter and spray it down with cold water. Once its thoroughly cleaned, install it back into the machine, plug it in, and turn it on.
If you suspect theres a problem with the washer, try accessing the pump filter. To access the filter, remove the machine from the wall. Then, take apart the back panel to locate the drain pump.
Turn off the water supply and remove the access panel at the bottom of your washing machine. Locate the drain pump, detach the hose from the inlet side, inspect it for debris, clear away any you find, and reattach it. Put back together and switch on the water supply. If you still see water draining into the drum, check air-drainage pressure at your external drain location.