How To Replace The Pump
Buy a new one to match.
- You can find a new pump by searching for your washing machines brand and model number online.
- Pro tip: Model numbers are usually stamped on a small metal plate located under the tub lid or on the top, side or back of the machine. Copy down all the plate information and use it to access online parts suppliers, or take it along to the parts distributor.
Family Handyman
Manually Drain The Washer
As I mentioned before, the first thing you need to do is get rid of the wastewater. You can either manually remove the drain hose or perform a master reset to force the appliance to expel the dirty water.
However, these are just quick hacks to drain water manually in case of emergencies. I strongly discourage using these tricks as an alternative to proper washer repairs and parts replacements.
Kenmore Washer Not Draining Or Spinning:
Kenmore top-load washing machines feature sleek, modern designs that are complemented by powerful cleaning technology. Start a load, schedule maintenance, and even download new wash cycles with intelligent features. A triple-action impeller is used in some top-load washers, which makes light work of dirty laundry.
One of the best reasons to choose a top-loading washer over a front-load washer is that you wont have to lean over! For added peace of mind, look for high-efficiency washers that use little water. Kenmore has the washer for you if you need to wash a full laundry or a tiny pile of delicates. Electrical machines are susceptible. They can make our life easy as well as hard.
If there are no clogs in the waste hose, the issue may be a faulty drain pump. Its also possible that the drain pump is clogged. The clog should be clear because the drain pump has a transparent cover. Follow the directions in the drain pump installation guide to clear the clog. There could be a problem with the drain pump if removing the clog does not affect it. Follow the instructions to repair the drain pump. Follow the instructions in the drain pump installation guide to replace the drain pump.
The waste hose in your washing machine can be clogged if it does not drain the wastewater. The repair of a clogged waste hose is as simple as cutting and unclogging the waste hose.
Follow the guidance in the waste hose fitting guide to separate and unclog the waste hose.
You May Like: Plumbers Putty For Sink Drain
Kenmore Washer Model #796 Front Load Washer
Kenmore washer model #796 front load washer – washer will not spin out – went to drain water from drain hose – no water will come out – so I unscrewed pump filter – water is pouring out of there – help
Posted byHeather BoyceonMar 05, 2014
-
An expert who has achieved level 2 by getting 100 points
MVP:
An expert that got 5 achievements.
Scholar:
An expert who has written 20 answers of more than 400 characters.
New Friend:
An expert that has 1 follower.
OK….I am here to RESCUE you…1st, DON”T do that anymore! You will get wet! LOL. Simple solution. You need a New Drain Pump replaced and installed. Once that is done. I do NOT want to hear about you going down there anymore and doing….That! LOL…Your machine will be happy and spin.and drain all day Long! If you need further help, reach me via phone at
The Drain Hose Is Kinked
If youve ever opened your dishwasher, only to find standing dirty water below the bottom rack, youve got a drainage problem. According to Sears Home Services expert Ron Meixner, there are three main reasons your dishwasher isnt draining properly. Heres what could be causing the issue and Meixners helpful solutions to fix it. Remember to consult your owners manual first for information on how to properly care for your dishwasher.
Don’t Miss: Sewer Smell In Shower Drain
Set Up The Bucket And Drain Hose
Ensure that the bucket is in a place where you wont accidentally knock it over you may want to place it firmly on or between several towels. Then, drop the house lower than the washer tub and into the bucket. If the bucket fills up, simply raise the hose back above the washer tub until you can empty the bucket. Drop the hose to start to fill it again.
If water doesnt flow freely from the washing machine tub through the drain hose and into the bucket, the filter may be blocked, so youll need to clear it before continuing.
How Do I Reset My Kenmore Elite Washer
The Kenmore washing machine does not have a reset button. Remove your machine from the power supply for 5-10 minutes to reset the washer by unplugging your machine or turning off the power at the breaker switch.
Wait the 5-10 minutes needed for all the electrical charge to leave your washing machine. Plug your washing machine into the electric socket again or turn the power on at the breaker switch.
Don’t Miss: Muriatic Acid To Clean Septic Drain Field
Inspect The Drain Pump
If none of the above works, your washing machine drain pump may have malfunctioned. As its name suggests, the drain pump is the central part responsible for draining the water from the washer.
If your Kenmore washing machine is under warranty, then you can get the drain pump replaced for free. However, if its warranty period is over, you will have to contact a repair technician to inspect and fix it for you.
Clean The Drain Pump Filter
Almost all Kenmore washers have a drain pump filter. However, over time, the filter gets clogged due to debris build-up and needs to be cleaned.
If you havent cleaned your Kenmore washer drain pump filter for quite a long time, there is a high chance its clogged and is the leading cause of your washer not draining the water.
Don’t Miss: Ge Dishwasher Not Draining Troubleshooting
Use Your Home Warranty Coverage
If youve followed all of these steps and your washing machine still wont drain, its time to call in a professional plumber or washing machine service technician. This is when complete home warranty coveragewith American Home Shield can help. With our ShieldGoldand ShieldPlatinumplans, you can enjoy awashing machine warranty.
When your machine breaks down in the future, dont pay expensive out-of-pocket costs by scheduling a repair person. Home warranty coverage helps reduce the cost of repair or replacing parts of your covered household itemsand gets your home back up and running in no time. With comprehensive coverage and flexible pricing and plans, a home warranty plan with us means budget protection when your washing machine wont drain.Learn about an American Home Shield® home warranty.
Look For The Clog And Pull It Out
The pump has a translucent housing, so you might even see the offending piece of clothing wrapped up in the pump.
- Loosen the clamp that holds the hose to the bottom of the tub and remove the hose.
- Pro tip: Have a bucket and sponge handy. Any water thats left in the machine will run out.
Family Handyman
Read Also: Installing Drain Tile In Basement
Check For Clogs In The Drain Hose Or Pump:
A sock or other small clothing piece sometimes gets caught in the drain system and clogs the hose or Pump. Displace the front panel of the washer and investigate these fields for any obstructions. If you notice it, take it out and see if the washing machine can drain.
If you remove the hose to clear an obstruction from the Pump, all of the water in the washer will spill out. Before disconnecting the hose, scoop out as much water from the drum as possible to prevent a mess.
Improperly Positioned Washer Drain
The first thing you need to check is the height of your washer drain. Ideally, the drain hose should be standing 30 inches from the base level. Most of the time, the drain hose slowly gets pushed too deep into the valve due to daily use. A simple fix would be to pull the hose up a few inches.
However, if the hose is at the proper height, you might want to check for signs of damages. Dont hesitate to get a part replacement if you notice any visible signs of deterioration such as stretching, cracking, or ruptures.
Also Check: French Drain And Sump Pump
Remove And Check The Drain Hose
Behind the washer, you will find the drain hose. Its connected to the appliance at one end while the other goes into a drain pipe that leads out of your house. First, verify that the hose isnt pinched or kinked anywhere, then pull the hose out of the pipe and inspect it for clogs.
If you find any debris, you should most definitely remove it. Then, set everything back up, turn the water and electricity back on and try starting your washer again. If the clog was the problem, it should now drain. If it still doesnt drain, or if you didnt find a clog, then make sure the power and water supply are shut off again before proceeding to the next step.
Damaged Water Pump Belt
Dismantle the back panel flap of your washer to reveal the water pump belt. Assess it by hand. Check if the belt shows severe signs of physical deterioration, cracking, and stretching.
If you decide its time to get a parts replacement, start by unscrewing the mounting bolt holding the pump belt upbut dont fully remove the bolts yet. Afterward, tilt the machine down a bit and remove the hoses connected to the water pump. Make sure theres a bucket underneath to catch all the excess water. After draining the remaining water, fully remove the bolts and dismantle the water pump.
Replace the belt with a new, durable one like 131686100 Washer Drive Belt by AppliaFit. Its a durable, high-quality, and easy-to-install aftermarket replacement part compatible with most Kenmore washers.
Don’t Miss: How To Drain Lymph Nodes In Neck
Inspect The Washing Machine Belts
If you have completed every step and still find that your washing machine wont drain, check if damaged belts are the cause of your drain problem. The manufacturers washing machine instruction manual should indicate the location of the belts. To check your belts, unscrew your washing machines access panel and check the main belt and the pump belt. Be on the lookout for any corroded, broken, or otherwise damaged parts.
Too Much Detergent While Using
If your Kenmore Series 70 is draining after usage, but it is going very slow, then you might have an easy fix. Using too much detergent can make your washer very delayed in draining and can make it seem like it has something wrong with it. If you are experiencing this, try to use half the detergent amount the next time you use your washer and see if it drains much more effectively.
Don’t Miss: Sealing Sink Drain With Silicone
Kenmore Elite He3 Washing Machine
@button if the washer won’t drain water the drain pump might be defective. It’s also common for a small sock or other article of clothing to get caught in the drain pump or in the drain hose. Check both for an obstruction before replacing the pump.
I would remove the drain plug from the filter at the water pump.
I would start by taking the lower front panel off. There are two bolts, one on each side of the panel, remove those. Once you have the panel removed, you will see a white plastic unit, that is your pump assembly. You should also see a round plug with a plastic tab across the front . That is your coin trap. Open the cap by twisting it counterclockwise and remove it. It may just be clogged. Make sure that you have a large tub or something under it. there is a lot of water coming at you.
You can download the service manual from from here.
The service manual will tell you how to run the diagnostics test so you can check to see if any error code is tripped.
Was this answer helpful?
Inspect The Drain Hose
This is the first thing to check when your Kenmore washer fails to drain the water. The drain hose is where the used water is pumped out of the washer.
If the drain hose is clogged, it wont be able to pump the water out. Most of the time, people forget to take items out of their pockets before throwing clothes into the washer, blocking the drain hose.
To check the drain hose, first, disconnect your Kenmore washer from the power source. Then, access the drain hose and check it for any clogs or obstructions. If there is any, remove it.
You May Like: Can I Use Drano In Shower Drain
The Air Gap Is Clogged
Solution: Some dishwashers use air gaps to prevent dirty water from backing up and contaminating your dishes. If one gets clogged, it can impact the appliances ability to drain. To tell if your dishwasher has an air gap, look for a small silver cylinder sitting by your faucet. If you have one, check to see if its clogged by removing the top cover and pulling straight up. Then, depending on the design, unscrew or release the tabs on the inner cap. Remove any debris or food buildup that may have accumulated and then reassemble the air gap.
Check Your Machines Inner Workings
If the hose drains when placed in the bucket, its time to check the machines inner workings for problems. This includes examining the drain pump, the lid switch, the belts and the water level control .
The drain pump is likely behind a panel that can be removed with a screwdriver. After you remove the drain pump, examine it for debris or obstructions and make sure the moving parts move freely. Sometimes simply cleaning the pump will do the trick. If nothing appears to be wrong with the pump, check to make sure all belts are in place and intact.
Find the lid switch and press it down while holding the lid open. The switch should click into place. If it doesnt, or if it seems loose, it may need replacing. Continue to check other parts of your machine. You may also find it helpful to look at the user manual.
The manual may have additional troubleshooting tips specific to your machine. Top load washers and front load washers have very different configurations, for example. If you dont feel comfortable messing with your machines insides, you might also call a washer repair technician at this point.
Read Also: Replace Garbage Disposal With Regular Drain
Kenmore Washer Wont Drain
If the Kenmore washer will not drain or is not draining properly, and it has a coin trap, remove the coin trap and clean it thoroughly.
First, check the drain hose to find out if it is kinked, twisted or bent. Next, remove the drain hose and see if there is anything obstructing its path.
In the following sections, we will discuss more ways to troubleshoot your Kenmore washer that does not drain.
Possible Problems Causing Your Kenmore Washer Not To Drain
When it comes to a washer that wont drain, it can first be overwhelming. Where do you even begin when your washer decides to be stubborn and wont empty the water? There are several reasons your Kenmore Series 70 washer wont drain those reasons include:
- Using too much detergent
- Problems or kinds with the hosing
- The switch for the lid could be faulty
More often than not, youll fix the issue by checking these three common problems. Sometimes, though, theres an issue thats a bit more deep-seated. Its not impossible to fix on your own, but it is more of a challenge to do so. First, try these three fixes below. If these dont help, then it would be a good idea to call in a professional.
Read Also: Shower Drain Distance From Wall
How To Fix Kenmore Series 70 Washer Wont Drain
Posted on Last updated:
Categories Storage and Cleaning
Home » Storage and Cleaning » How to Fix Kenmore Series 70 Washer Wont Drain
How do I get my Kenmore washer to drain? If you are asking yourself this question, then this post is meant for you. The Kenmore 70 series are washers and dryers from one of the biggest appliance manufacturers. They include a top-loading unit and large capacity drums.
Although Kenmore does not manufacture Kenmore Series 70 anymore, you can still buy the washer and the replacement parts from third-party vendors. If your washer is not draining, the first thing you need to do is locate the problem.
Is It The Drain Hose Thats Causing The Problem
Likely, the hose that transfers water from the back of the unit stops it from draining properly. A kink could obstruct the water flow through the washing machine hose, or the device could be stuck too close to the wall, blocking water flow through the hose. Its also possible that the hose has become clogged. Disconnect the drain hose and look inside with a spotlight for any difficulties.
If you cant reach whats clogging the drain, take it outside and run water through it with a garden hose. Then, reconnect the drainpipe to the machine, switch on the power, and run the rinse cycle to notice if the water is removing correctly.
You May Like: Drill Drain Hole In Ceramic Pot