Kenmore Elite Washer Not Draining
If your Kenmore Elite washer is not draining properly, there could be a few different reasons why. In this blog post, well go over some of the potential causes for a Kenmore Elite washer not draining and how to fix them.
One potential reason for a Kenmore Elite washer not draining is that the drain pump has failed. The drain pump is responsible for pumping the water out of the washer tub. If the drain pump has failed, you will need to replace it.
Another potential reason for a Kenmore Elite washer not draining is that the drain hose is clogged. The drain hose is what carries the water from the washer tub to the drain. If the drain hose is clogged, the water will not be able to flow through it and will back up into the washer tub. To fix this, you will need to clear the clog from the drain hose.
A Kenmore Washer That Wont Work Because The Door Wont Open
If the Kenmore washer is front-loading, then its door automatically locks when it is washing. If the washer senses that the water hasnt drained, then the door will not unlock. If this is the case, look for clogs in your water pump as we described above. You can also check your washers drain hose to see if there are obstructions. Finally, set your drain cycle again and let it run. Once the cycle is complete, if you have fixed the problem then the door will unlock.
How To Check The Water Pump And Hoses
First, it is located underneath the spray arm and lower rack. Examine the pump and see if any dirt is clogging the pump.
If not, check it for broken components. If water is not draining from the tub, the drain pump may need to be replaced.
You must replace the pump if it has broken components since its difficult to repair. Check to make sure the drain hoses are not kinked. Small clothing can get stuck in the drain hose or attached to the drain pump.
If this is the case, you will need to remove the hoses from the pump to clear them out. The internal impeller in the drain pump can also break and can be replaced.
Replace the hose if its crushed. The drain hose must not extend more than 4 inches into the tub. Remove the excess hose.
Read Also: Drain Sticks Where To Buy
Kenmore Washer Not Draining Completely
There are a few things that could be causing this. Check the following:
-The washer is not level. Use a level to check and adjust the legs accordingly.
-There is something blocking the drainage hose. Remove the hose and clean it out.
-The drain pump may be damaged or dirty. Clean or replace the pump as needed.
Kenmore 110 Series Washing Machine Wont Drain
Wondering what to do when your Kenmore 110 Series Washing Machine won’t drain after its washing cycle? Try these fixes to get your washing machine working, again!
Does your Kenmore 110 Series Washing Machine no longer drain water out of its basin after its wash cycle? Kenmore 110 Series Washing Machines are susceptible to a range of problems that could cause them to stop draining. Check the following causes to identify and solve the problem.
Don’t Miss: Jay R Smith Floor Drain
Too Much Detergent While Using
If your Kenmore Series 70 is draining after usage, but it is going very slow, then you might have an easy fix. Using too much detergent can make your washer very delayed in draining and can make it seem like it has something wrong with it. If you are experiencing this, try to use half the detergent amount the next time you use your washer and see if it drains much more effectively.
The Washer Doesn’t Drain
Washer doesn’t drain and I can not hear the timer like it wants to trip to drain and spin any help out there
If your Kenmore 110 Series Washing Machine is not draining after a wash cycle, see the Kenmore 110 Series Washing Machine Wont Drain problem page for possible causes and solutions.
Belt, Water Pump
If the washer won’t drain the pump belt might have broken or might have worn out. Check the belt and replace it if it shows signs of excessive wear.
Drain Pump
If the washer won’t drain water the drain pump might be defective. It’s also common for a small sock or another article of clothing to get caught in the drain pump or in the drain hose. Check both for an obstruction before replacing the pump.
Other Causes and Conditions
Clogged Pump or Hose
If the washer won’t drain there might be a clogged pump or hose. It’s common for small socks or other small clothing items to get into the water drain system and clog the hose leading to the pump or the pump itself. Remove the hoses from the pump in order to remove the article of clothing. Keep in mind that any water in the washer will pour out of the hoses when removed.
Drive Belt
If the washer won’t drain, should check the drive belt. If the belt is broken or if it isn’t tight on the pulleys the washer won’t drain properly, if at all.
Lid Switch Assembly
Door Lock Motor and Switch Assembly
Drain Hose
Coin Trap
Was this answer helpful?
Recommended Reading: How To Change Sink Drain
Door Lock Motor And Switch Assembly
The door lock motor and switch assembly is located behind the washer tub, on the back of the washer. The door lock motor turns the door lock switch on and off. If the door lock motor is defective, the washer will not start.
To check the door lock motor:
Unplug the washer. Remove the screws that secure the back panel to the washer. Disconnect the wires from the door lock motor. Remove the door lock motor from the washer.
If the door lock motor is defective, replace it. If the door lock motor is not defective, check the door switch.
How To Remove Debris And Kinks From Your Hose
The pump and the hose are usually the two most common areas that are having trouble if you have a washer that is not draining. Check the pump while youre fixing the hose as well to make sure everything looks great in that area.
You May Like: Professor Amos Superfast Drain Cleaner Home Depot
Check For And Remove All Clogs In The Drain Hose
Once the water has fully drained out of the tub, check the drain hose for any debris, clothing, or soap blockages, all of which can make the washing machine drain clogged. To check for clogs, loosen the clamp connecting the hose to the bottom of the tub, then inspect the inside. If you see something blocking the hose or its connecting parts, remove it with the pliers, then reconnect the hose.
Use Your Home Warranty Coverage
If youve followed all of these steps and your washing machine still wont drain, its time to call in a professional plumber or washing machine service technician. This is when complete home warranty coveragewith American Home Shield can help. With our ShieldGoldand ShieldPlatinumplans, you can enjoy awashing machine warranty.
When your machine breaks down in the future, dont pay expensive out-of-pocket costs by scheduling a repair person. Home warranty coverage helps reduce the cost of repair or replacing parts of your covered household itemsand gets your home back up and running in no time. With comprehensive coverage and flexible pricing and plans, a home warranty plan with us means budget protection when your washing machine wont drain.Learn about an American Home Shield® home warranty.
Don’t Miss: Drain Flies Get Rid Of
Manually Drain The Washer
As I mentioned before, the first thing you need to do is get rid of the wastewater. You can either manually remove the drain hose or perform a master reset to force the appliance to expel the dirty water.
However, these are just quick hacks to drain water manually in case of emergencies. I strongly discourage using these tricks as an alternative to proper washer repairs and parts replacements.
Kenmore Washer Wont Drain
If the Kenmore washer will not drain or is not draining properly, and it has a coin trap, remove the coin trap and clean it thoroughly.
First, check the drain hose to find out if it is kinked, twisted or bent. Next, remove the drain hose and see if there is anything obstructing its path.
In the following sections, we will discuss more ways to troubleshoot your Kenmore washer that does not drain.
Recommended Reading: What To Do If Your Washer Is Not Draining
Defective Lid Switch Assembly
The switch assembly on a front load washer detects whether the lid is open, and the lock ensures that the lid stays shut when the washer is in use. The lid switch/lock assembly can succumb to electrical or mechanical failure. If the lid will not stay locked, the load will not spin and the washer will not drain.
Have a service technician inspect your washer to eliminate other potential problems that may cause the lid switch or lock to malfunction. Your technician may need to replace a faulty switch or lock assembly.
A front load washer is a major investment, and even the slightest fault can send you into a spin. However, proper use and maintenance can mitigate draining issues with your washer. At Capital City Appliance Service, Inc., we understand how important it is to have your washer working properly at all times. If you need service for your appliance, get in touch with us today.
Need Help with Your Broken Appliance?
It Could Be Issues With Hosing
Another important factor that can make your washer not drain at all is issues with the installation of the hose or with blockage of your hose. The first major reason is with the installation. Too high of a hose off the ground will not let the machine drain right and could be your reason for having problems.
When installing your hose into your washer, you need to make sure that it is less than 8 feet off the ground. Too high of a hose is terrible news because your washer is going to be fighting gravity hard to pump the water out of your washer. The other common reason your hose can be messing with you is if it is clogged with a piece of debris.
You May Like: Freestanding Tub Flexible Drain Hose Installation
Possible Problems Causing Your Kenmore Washer Not To Drain
When it comes to a washer that wont drain, it can first be overwhelming. Where do you even begin when your washer decides to be stubborn and wont empty the water? There are several reasons your Kenmore Series 70 washer wont drain those reasons include:
- Using too much detergent
- Problems or kinds with the hosing
- The switch for the lid could be faulty
More often than not, youll fix the issue by checking these three common problems. Sometimes, though, theres an issue thats a bit more deep-seated. Its not impossible to fix on your own, but it is more of a challenge to do so. First, try these three fixes below. If these dont help, then it would be a good idea to call in a professional.
Cause : Clogged Waste Hose
If your washing machine does not automatically drain the wastewater, the machines waste hose might be clogged. To unclog the waste hose, remove the hose from the back of the washing machine by unclipping it. Then, clear it out using running water and a toilet snake. After the hose is cleared, snap it back in place on the back of the washing machine and try to use the machine again.
You May Like: How To Clean Outside Drain
Problem With The Drain Hose
First, check the drain hose to determine if it has any kinks or twists. If it does, try to make sure that the path isnt obstructed with anything such as using a wire hanger and sliding it inside.
If still, nothing comes out after trying to clear out any obstruction from within your hose, you should probably go ahead and replace it altogether.
Related Guides
Cause : Clogged Drain Pump
If your washing machines waste hose is cleared of any clogs and it is still not draining properly, your machine may have a faulty drain pump. Because the drain pump has a translucent cover, a clog may be visible in the pump without having to take it apart. If you see a clog, use the Kenmore 110 Series Washing Machine Water Pump Replacement Guide to remove the machines water pump.
Also Check: 100 Ft Drain Auger Cable Replacement
Is It The Lid Switch Thats Causing The Problem
If the lid switch is crushed, the unit will be incapable of draining perfectly. The lid switch is usually a tiny plastic switch located underneath the washers lid or door. Open the washer and press the button to see if its working correctly. The controller can need to be replaced if you dont hear a clicking sound.
Is It The Pump Or Something Else
Locate the Pump using the manufacturers diagram for your washer model. Its customarily situated in the machines front or back. Prepare a screwdriver in case you need to remove a panel to get to it. Remove the panel by detaching the Pump and opening it. Thoroughly rinse the screen.
Ensure the fan blades or arms are moving freely and that none of them are broken or missing by turning them. Look inside the Pumps outlet to see if something has become stuck. Check for holes or leaks in the Pump. You can need a new one if the blades are missing or the Pump is leaking.
Also Check: How Long Do Drain Fields Last
What To Do When Your Washing Machine Wont Drain
A functional washing machine is an effective tool for getting dirt, sweat, and stains out of clothing. The exact way the washer cleans your clothes depends on the precise settings you choose, but the basic premise is the same: first, the drum fills with water when you hit Start. After the wash cycle, the drum drains, and the first spin cycle begins. Then, the drum refills to rinse the clothes with clean water. Finally, the machine drains one final time and spins the clothes dry.
If you open the lid after the washer stops running to find your clothes swimming in water, something is obviously wrong. The drum wont drain, that much is certain, but why? To get to the bottom of it, follow these troubleshooting tips before you call in a professional for help.
What To Do If Kenmore Series 70 Washer Wont Drain
How do you get your Kenmore washer to drain? Tired of checking what is the problem with your washer? What is the simplest way to fix the washer? This post might help you to solve your problems.
A washing machine is basically a big tub that repeatedly fills with water and then drains, spins to wring clothes dry, and has a device for stirring the contents upeither an agitator in the middle of a top-load machine or a rolling drum in a front-loading machine.We all know that The Kenmore 70 series are washers and dryers from one of the biggest appliance manufacturers. They include a top-loading unit and large-capacity drums.
Although Kenmore does not manufacture Kenmore Series 70 anymore, you can still buy the washer and the replacement parts from third-party vendors.
There are might common problems every time our washer cannot do the task that they intended to. There might be the best way on how to easily determine the problem of our washer.
If your washer is not draining, the first thing you need to do is to see if you can locate the problem before contacting Kenmore. This saves your money on out-of-warranty repair fees.
Don’t Miss: Water Coming Up From Floor Drain
Defective Door Lock Motor And Switch Assembly
The door lock ensures that the door is closed when the washer is being operated. When the door lock is locked, it allows the washer to start or continue operating.
Once youve switched on your washer, for example, the next step is to close its door and if the door does not shut properly or latch with the lock, this often means theres a problem with both how it shuts and how well it has been engineered.
After which, it can affect how well your appliance actually performs. This is why you should make sure you check both how tightly it latches as well as make sure that there are no signs of electrical damage .
Otherwise, be prepared for things like not getting enough lift on your clothes or not getting them clean if, in fact, this does happen.
What To Do For A Clogged Pump In Your Kenmore Washer
The first important step is to unplug your machine and then access the central panel of your Series 70 Washer. You should be able to see or feel if the pump is clogged or needs attention. This is the most apparent cause for lack of draining because that is what the pump does after a spin cycle is done with your Kenmore washer.
While you are already inspecting the pump, analyze other parts of the area, and see if anything looks broken or has debris in it that could be causing problems. According to a few YouTube videos online, you should also check the pulley system in the pump area and make sure it is running smoothly. Without the pulley, a whole slew of problems can erupt with your washer.
You May Like: Ridgid Power Spin Drain Cleaner