Check The Drain Pump & Internal Drain Hose
If you have completed the checks above and the drain pump is not working or the error code persists, the drain pump or internal drain hose may have a problem that will require accessing them to fix the issue.
Access to the drain pump will depend on your model. If you have a top-loader washer, you will likely need to place the washer on its back so that you can access the drain pump underneath the washer. If you have a front-loader washer, you may need to remove either the front control panel and door seal or an access panel at the back of the washer.
Follow these steps to check the drain pump and internal drain hose:
Lg Washer Wont Drain Heres What To Do
If your LG washer isnt draining after you run a wash cycle, do not panic. While this is a frustrating problem, it can often be very simple to fix.
Read on to find out what usually causes a washer to stop draining and find out what you can do to fix the problem.
The following models of LG washer are covered by this guide:
RLM20K
WM3470HWA
Lg Washer Wont Drain / Keeps Draining
Categories Home and Kitchen, LG Washer, Washer & Dryer
If your LG washer has faulty problems like not draining water or keeps draining, something needs to be done. Some of these failures can be very irritating and frustrating, especially if you dont know the cause however, you do not need an expert to get it fixed as you can always diagnose and provide a solution by yourself. Why, then, does your LG washer keep draining or wont drain?
If your LG washer wont drain or keeps draining, it might be having malfunctioning parts or a drainage problem altogether. You can fix some of these with ease, and some will require a professional. However, these categories may include various possible causes that may take some time to troubleshoot.
This article narrows down to the most common reasons why your LG washer wont drain water, why it wont drain water fully, wont stop draining, and why the drain pump wont stop. It aims at helping you troubleshoot your washer more effectively. Accordingly, this article will help you conduct a DIY fix instead of going for professional repair.
Don’t Miss: Cleaning Drains With Baking Soda Vinegar
Lg Washer Part Failure
If you still notice your LG washer not draining, a part failure may be responsible.
The following parts can cause draining problems when they fail, requiring a professional LG washer repair:
- Drain pump: The drain pump expels water out of the washer tub and into the drain hose. If its impellers are broken or obstructed or its motor fails, water wont drain.
- Lid switch: As a safety precaution for top loading washers, the lid switch signals the washer to start only when the lid is closed. If it malfunctions, youll notice the washer isnt spinning properly or draining even if the lid is shut.
- Water level switch: This switch monitors the water level inside the washer, signaling the timer and water inlet valve when more or less is needed. If the switch is faulty, youll notice the washing machine isnt filling with water or is filling too much and cant be drained.
Action Appliance Repair can help with all your LG washer repair needs. Schedule your service today!
Problems With The Water Level Sensor
If a continuous drain began suddenly, then the pressure switch was probably guilty. It is he who controls the water level in the tank, giving a signal to the control board about the beginning and stop of the intake from the water supply. When a malfunction occurs, the sensor cannot track the degree of fullness of the tank, which leads to exceeding the maximum mark and emergency “self-drain”. That is, the machine lowers the water into the sewer, protecting the electronics from leakage. The following problems lead to a breakdown of the pressure switch:
- oxidized contacts of the device
- circuit wiring
- violation of the sealing membrane of the sensor
- damage or clogging of the pressure pipe.
To check the operation of the pressure switch, it must be removed from the machine. Disconnect the washer from the network, remove the top cover and at the back wall of the case we are looking for a round plastic cover. We turn off the fasteners and carefully inspect the part. If traces of oxidation are noticed at the contacts, then we clean the tips with a knife. But when there is damage to the tube or a suspicion of a wiring short circuit, a replacement is ahead. Replacing a level sensor with a new one is simple and inexpensive.
Before disassembling the washing machine, you must completely disconnect the unit.
You May Like: How Much Do French Drains Cost
Check To See If It Will Drain With The Help Of Gravity
Find a large bucket, place it on the floor and place the end of the drain hose into the bucket. If theres no clog, the water should drain on its own owing to gravity. At this point, you can be fairly certain there are no clogs in the hose, and the problem is either related to the inner workings of the machine the drain pump, a belt, the lid switch, etc. or a clog in the drain pipe.
If your machine doesnt drain when you put the hose in the bucket, then the issue is still most likely a clog somewhere deeper in the hose that you cant see.
Troubleshoot Why Your Lg Washer Wont Drain
When your washer wont drain it seems clear that theres either a part malfunction or a drainage problem. Yet these two categories include so many possible causes that troubleshooting them uses time youve already spent wringing out wet clothes. Well narrow down the most common reasons why your LG washer wont drain, including a clogged drain hose or malfunctioning door latch.
Read Also: How To Make Sinuses Drain
Lg Direct Drive Washing Machine Error Code Ue
Possible causes:
- Load could be too small.
- Load might be out of balance.
- The washer features an imbalance detection system. If you load individual heavy articles this system might make it stop spinning .
Potential solutions:
Quick Tip: If the clothes are still extremely wet when the cycle finishes, add smaller items of laundry to try and balance the load then rerun the spin cycle.
Kinked Or Clogged Drain Hose
If your LG washer not draining is causing a problem, check for kinks in the drain hose. If there are any kinks in the hose, it can stop the water from draining properly.
To check for kinks: Unplug your washer and remove the drain hose. Straighten out the hose and check to see if the water drains freely. If there are any kinks, remove them and plug in your washer again.
Remove any clogs from the drain hose: If the water is not draining because of a clog, you will need to remove the clog before you can continue troubleshooting. To do this, unplug your washer and remove the drain hose. Use a plunger to clear any clogs that may be blocking the drainage path. Make sure the plunger fits tightly over the drain opening and plunge up and down for several minutes. Once the clog is cleared, reattach the hose and plug in your washer.
Recommended Reading: Why Does My Drain Smell
Connect With An Appliance Repair Tech
No in-home service calls. No appointments.
The best way to clean this part is to run it under warm water.
Youll also want to use a rag or cleaning brush to clean inside the housing for the drain pump filter.
Once everything is clean youll replace the cap on the drain hose and connect the hose to your washer once again.
Just be sure the filter is put back in place securely.
Install the cover over the drain pump filter by turning it clockwise this time.
After youve cleaned the filter and re-secured it so its free from blockages you can try your LG washer by running a small load to see if the OE code is cleared.
To test the drain pump its best to run a spin only cycle.
Do this by pressing POWER to turn your washer on.
Then press the SPIN SPEED button until HIGH is visible.
Go ahead and press the START/PAUSE button to begin the spin cycle.
Do you hear a humming noise? If so, your washer is beginning to drain.
However, if you do not you may want to hire an appliance repairman to physically check the drain pump.
This part is located inside the washer and is a bit harder to check if youre not comfortable working with electrical components.
If you feel confident you can handle this job, this is how youll locate the drain pump.
2. Then, youll need to locate the screws holding the top of your LG washer in place, and remove them.
3. Next, press the release tab on the soap drawer and remove it.
Inspect The Drain Pump
If none of the above works, your front-load washing machine drain pump may have malfunctioned. As its name suggests, the drain pump is the central part responsible for draining the water from the washer.
If your LG front loader washing machine is under warranty, then you can get the drain pump replaced for free. However, if its warranty period is over, you will have to contact a repair technician to inspect and fix it for you.
Also Check: Bathroom Faucet With Pop Up Drain
Clothes Caught In Drain Pump
Like the drain hose pipe, the drain pump is likewise vulnerable to obstructions from little clothes products or particles. To assist in draining pipes, the pump siphons utilized water from the washer tub through the drain hose pipe. A stopped up pump can lead to an LG washer not draining pipes totally or at all. This can take place more quickly if the drain pump filter is likewise blocked.
Describe your user handbook to figure out how to access the drain pump and examine it for obstructions. A lot of lie on the bottom of the washer behind a rear panel. If the pump has no noticeable blockages however is exceedingly loud, it might have malfunctioned and needs expert replacement.
Whether you discover your washer not filling with water or not draining pipes effectively, D& T Device Service Business can assist. Call us for a quick and expert repair work of any washer problem.
Drain Your Washer Manually
If you cant get the washer to drain using the steps above, you will have to manually drain the remaining wash water to complete the rest of the methods. The process is different for top-loading and front-loading models.
For front-loaders:
To manually drain a top-loader, you will need to use the washers main drain hose. Heres how to do it:
Don’t Miss: Connecting Sink Drain To Wall Pipe
Lg Front Load Washer : How To Clean The Drain Pump Filter
Your LG Front load washing machine is equipped with a drain pump filter that makes lost button or loose change a thing of the past.
In this video, we will show you how to retrieve any lost items and keep your LG washer running properly for years to come.
LG recommends cleaning out the drain pump filter of any lost items and lint buildup on a monthly basis.
Before we begin: Make sure the unit is empty, turned off, and drained of any visible water in the tub.
LG: Life’s Good
How To Reset Lg Direct Drive Washing Machine
Just unplug it and leave it unplugged for about 30 minutes .
You then plug the machine back in and see if it will work!
You can also reset it by turning off the circuit breaker for a while then turning it back on.
Try it- it might save you a lot of time and trouble.
Having cleared up that, let us now go into particular LG direct drive washing machine problems and how to fix them:
Don’t Miss: Outdoor Shower Pan With Drain
Lg Washer Drain Pump Wont Stop
If your LG washer drain pump wont stop, there are a few possible causes. The most common cause is a clog in the drain hose or pump. Other possible causes include a faulty door switch or control board.
To fix a clog, start by unplugging the washer and removing the drain hose from the back. Next, use a plunger or pliers to clear any obstruction in the hose. If that doesnt work, you may need to replace the drain pump.
To fix a faulty door switch or control board, start by unplugging the washer and checking the door switch for continuity. If the switch is faulty, replace it. If the control board is faulty, replace it with a new one.
Check Your Machines Inner Workings
If the hose drains when placed in the bucket, its time to check the machines inner workings for problems. This includes examining the drain pump, the lid switch, the belts and the water level control .
The drain pump is likely behind a panel that can be removed with a screwdriver. After you remove the drain pump, examine it for debris or obstructions and make sure the moving parts move freely. Sometimes simply cleaning the pump will do the trick. If nothing appears to be wrong with the pump, check to make sure all belts are in place and intact.
Find the lid switch and press it down while holding the lid open. The switch should click into place. If it doesnt, or if it seems loose, it may need replacing. Continue to check other parts of your machine. You may also find it helpful to look at the user manual.
The manual may have additional troubleshooting tips specific to your machine. Top load washers and front load washers have very different configurations, for example. If you dont feel comfortable messing with your machines insides, you might also call a washer repair technician at this point.
You May Like: Moen Tub Drain Brushed Nickel
Opening The Washer: Top And Control Panel
To get at the drain pump, youâll need access to the front and rear of the washer. On the rear, youâll find some connectors between the top and the back. Unscrew the bottom screws on both sides, then slide the top back about an inch. Pull it back too far, and it will hang up on stuff inside and not come off.
With the top off, youâll find the guts of your washer exposed. Thereâs a large plastic drum suspended by some springs, a power converter, some tubes⦠really, the sort of stuff youâd expect to find in a modern washer.
The next step is to remove the control panel. Start by taking the âstuff trayâ out. The big button labeled âPushâ in the center of the back section will release a catch and let you pull the whole drawer out. Our water does have a bit of sediment that builds up over time, so itâs a good time to clean it out.
Once the tray is out, you can remove the two screws on either side. Theyâre longer than the other screws youâll pull out, if you donât keep track of where stuff goes.
Seriously, though. Keep track of where stuff goes. There are several different types of screws in here, and they donât exchange with one another.
Thereâs one more screw holding the control panel on, and itâs on the back in the other corner. Youâre taking out the round headed screw, not the lower hex headed one – that doesnât need to come out.
Now is actually a good time to clean most of the washer, because youâll have it open.