Check For Clothing Or Other Clogs
A sock, mask, or another small piece of clothing can get stuck in the washing machine. There are several places in the device that you will need to check, and the procedure you will have to follow will differ depending on the type of machine you own.
Note: Before you begin working on your washing machine, you should unplug the unit to prevent injuries.
For front-load washers, you need to remove the front panel, which you should be able to do with a flathead screwdriver. On most devices, you do not have any screws to remove.
There should be two clips on the bottom of your washer. If you pull forward on the front panel, it should unclip from the unit. Once you have it unclipped, you should be able to push up and pull the piece out.
If your unit does have screws, you will need to lay it down on the back to access the screws. They should be at the base of the unit directly above the feet. Once you unscrew the two screws, you should be able to push up and pull the panel off.
Once you have the access panel off, check for any items that dont belong. You can also perform a few maintenance tasks to make sure your unit is running efficiently.
Empty The Lint Filters
Did you know there is a lint filter in your washing machine? Well, most washers actually have a trap that keeps larger items from clogging the drain line.
Typically, these filters are self-cleaning, but if your machine is not draining, you should check to make sure that nothing is clogging the filter.
Washing Machine Isnt Level
Whats one of the most common causes for a Samsung washer not draining? A machine thats not level will cause draining problems and can also be responsible when your washer wont spin properly. If a leveling tool reveals that your machine isnt level, first check the floor underneath the washer. Carpeting or a slippery surface can make the floor uneven or cause rocking.
If the floor is level and the machine can still rock back and forth, check the washers leveling feet to make sure theyre even. Rotate the leveling feet counterclockwise to lower them and clockwise to raise them until theyre even.
Read Also: Water Heater Won’t Drain
Why Do Washing Machines Stop Draining
There are many reasons why your washing machine might not drain properly. Most homeowners do not realize that you need to perform routine maintenance to keep your washer running correctly.
If you do not keep your washer clean, it can get a clog. There are other reasons your unit may stop draining, like a broken lid switch, a bent drain hose, a clog in the drain line, or any other issues that can cause water to remain in the basin after the cycle is complete.
If youre looking for a trusted, industry-leading home warranty company, we recommend Choice Home Warranty. Choice Home Warranty is an industry leader in providing home warranties for washing machines, and right now you can take advantage of their current promotions that get you $50 Off + 1 Free Month and Free 30-Day Cancellation. Get a free online quote or contact a specialist at 929-400-6169 before these deals end.
Your next best option is American Home Shield which offers $50 Off and The Service Fee of Your Choice. Get a free quote online or request more information directly at 866-464-7521.
Straighten The Drain Hose
The first natural place to look is your drain hose. The washer has a special hose that carries dirty, soapy, and rinse water away when the unit drains. This hose connects to a drain in the floor or the wall nearby. Drain hoses very commonly get either twisted and blocked from the outside or clogged from the inside.
The most common cause for a blocked drain hose is a walking washer. Your washer may have wobbled backward enough to pinch the drain hose and stop the draining. Locate your drain hose and track it all the way from the washer to the drain aperture. Shake it clear and then put the washer back in place, ensuring the drain hose is not kinked or pinched. Twists should be avoided or wide, if possible.
Read Also: Home Depot Dishwasher Drain Hose
Check For A Blocked Pump Filter
Next you need to check for blockages in the pump filter if your washing machine has one. Most do. You will need to have drained out as much water as possible before removing the filter. Also, put down large bath towels before removing the pump filter to soak up the water that will inevitably come out.
Check That The Drain Pump Is Working
If there is nothing that is blocking the drainage system, the problem might be with the pump itself. Without the power of the pump, the drainage system cannot function.
Replacing the drain pump is a job best left to a professional appliance repair technician, but you can do some investigating to find out whether you need to hire one.
Check for the following signs of a faulty drain pump:
- There is no noise from the pump when you run a wash cycle.
- There is a noise, but it is a loud, unusual sucking or grinding sound.
- There is no problem draining the washer manually and no obstructions in the drain hose or filter.
- Remove the drain filter and use your fingers to turn the impeller. It should turn freely.
- There are broken pieces of plastic inside the drain filter.
Recommended Reading: Bosch Dishwasher Is Not Draining
Why Is My Whirlpool Washer Not Draining Completely
If your washer isnt properly draining, this might be due to a clogged drain hose, a pump obstruction, or even excessive sudsing. Stick around for more reasons and solutions!
In this article, we answer the following questions:
- Why is my whirlpool washer not draining completely?
- How do I test the drain pump on a Whirlpool washing machine?
- How often should I drain my washing machine?
Related:
Check Out The Drain Pump
Washing machines use a pump to remove water from the machine, and this can also get clogged. If that happens, you can open up the washer and access the pump. Models vary, so check your user manual to see where the pump is located. Drain pumps are usually translucent, so you may be able to see the clog from the outside.
Following the user manual, disconnect the drain pump to access the clog. Have a bucket handy since water may come out when you do this. Then, you can just use pliers to pull the clog away. In some cases, the pump itself may be bad. This usually results in leaks and strange noises, and it will need to be replaced to drain the machine.
Read Also: How To Stop Apps From Draining Battery Android
See If You Can Drain The Drain Hose
The drain hose is the line that carries water away from your machine. It is gray on many models, and it typically just sits loosely in a large pipe on the wall. This drain hose almost always has some water in it, so you will need to drain it before you move the washing machine or clean it. If your washing machine is broken, it is still important to try to drain the drain hose. Often, the whole reason for a washing machine that won’t drain is just a clog in the hose, so you need to disconnect it and take a look inside.
To do this, you can usually just wiggle the hose and slide it right out. Hold it upright in the air because if the end goes below the waterline in your washer, water may start to shoot out. When you have a bucket ready, lower the drain line and place it in the bucket. If water drips out or moves slowly, you probably have a drain clog. Fortunately, drain lines are short enough that removing a clog is simple. Just break up the blockage with a plumber’s snake or an unclogging solution.
Clear Tube Before Air
- Push a straightened wire coat hanger 10 inches into the small air-gap tube.
- Set the dishwasher to drain/cancel/reset and close the door to start draining as you move the coat hanger up and down to break up the obstruction.
- Look for a column of water shooting up three inches above small air-gap tube.
If you don’t have an air-gap up by the kitchen sink, your dishwasher drain hose goes directly into your garbage disposal or your kitchen sink drain. If this is the case, proceed to Step 4.
Also Check: Home Depot 4 Inch Pvc Drain Pipe
Check The Drain Hose For Clogs
The drain hose is responsible for moving water from your washing machine outside of your home. If there is a clog in the line, the water is unable to drain properly.
It is not uncommon for sediment and debris to buildup in the line. So, if you have an older machine, a clog is probable.
Note: Ensure that your device is unplugged before you begin working on the drain hose. You will also want to gather some towels, a large plastic container with a low edge, pliers, a pipe cleaner or plumbers snake, and an antibacterial cleaner.
When you have all of your materials together, you will disconnect the drain hose by gently wiggling the connection on the back of the washer using pliers. Once you remove the hose, you can hold it down into your plastic container to see if the water drains.
If the water does not drain or it comes out slowly, use the pipe cleaner to remove any blockages. Once the drain is clear, your machine should operate properly.
Be sure to mop up any water from your machine. Spray the area with cleaner, then mop it up with clean water and wait for it to dry before replacing your washer to avoid mildew from growing underneath.
Check To See If It Will Drain With The Help Of Gravity
Find a large bucket, place it on the floor and place the end of the drain hose into the bucket. If theres no clog, the water should drain on its own owing to gravity. At this point, you can be fairly certain there are no clogs in the hose, and the problem is either related to the inner workings of the machine the drain pump, a belt, the lid switch, etc. or a clog in the drain pipe.
If your machine doesnt drain when you put the hose in the bucket, then the issue is still most likely a clog somewhere deeper in the hose that you cant see.
You May Like: How To Create Well Drained Soil
Clean Washer Drain Pump Filter
If your front load Samsung washer wont drain, the drain pump filter may be clogged. In front-loading machines, this filter prevents small articles of clothing and debris from damaging the drain pump. However, if it gets clogged, the washer may not drain properly. Cleaning the filter on a monthly basis can help prevent blockages.
Heres how to clean the drain pump filter when you find your front load Samsung washer not draining properly:
Do you still have washer draining problems even after these troubleshooting tips? A faulty door latch or Samsung drain pump problems may require a professional washing machine repair service. Call Appliance King of America to help with all your laundry appliance needs!
Check The Door Lock Switch
Washers will not run if the door or lid is not closed. This is achieved by a failsafe switch that will not let the cycle run until the door locks and it is engaged.
If the door lock assembly has become loose, it can fail to sense when the door or lid is closed. This causes the draining function to stop.
If this is the problem, you will most likely see the error code OE on your digital display. Press the door or lid firmly shut to see if this kickstarts the draining process.
If this is your problem, you should call a professional appliance repair technician to conduct the repair.
Don’t Miss: How To Clear Clogged Drain Pipe
Test For Success Or Try Again
Each time you try a solution, test to see if your fix was successful. This is important to learn what the problem was and aptly fix it, without diving unnecessarily into your washer cabinet. Let yourself know when you are done by testing frequently. To test, run an empty load of laundry, set to the shortest full-cycle settings. Wait for the cycle to finish and check to see if the water has drained. If so, pat yourself on the back and enjoy your laundry machine.
If the washer still isnt draining, you may need professional assistance to hunt down the problem. A trained appliance repair technician can take apart the washer and examine every part that contributes to washer draining. They can also more promptly determine whether the problem is inside the washing machine or underneath the house instead. If you are in over your head, if you dont have time to do DIY repairs, or if your washer isnt fixed when you try the steps, contact us today. Our team of professional appliance technicians is here to help with all your home appliance concerns. We are always happy to consult with a new or returning client.
Remove Any Kinks In The Hose
GEs washer may have a clog in the hose, filter, or pump, which can cause the washing machine not to drain.
Troubleshooting steps:
- To fix this, turn off the washer and unplug it from the power outlet.
- Then, remove any kinks in the hose and double-check that its connected to your GE washer properly.
- If there are no kinks, check for any holes at the bottom of the washer and open them up to see if water comes out.
- If this does not work, turn off the water coming into your house and clear any debris from around your homes supply valve or in your yard.
- Does the issue still persist? Then, there may be an issue with your drain pump. In this case, you will need to consult with a GE service center to provide you assistance.
What Are The Ways Of Troubleshooting A Washer That Wont Drain
Your washing machine drain system uses a pump and hoses to clear water out of the machine after each cycle. When components break or there is a water flow obstruction, the water will not drain.
If your device is not draining, it could be a sign that you will need to replace your device or call a technician. However, the cause of your washer woes could be something you can quickly fix yourself.
So, follow these step-by-step DIY tips before you call a maintenance specialist or start shopping for a new Maytag.
Final Advice When Your Washing Machine Wont Drain
One of the best ways to keep your washer running well is to invest in an extended warranty or a home warranty. An extended warranty will cover repairs after your manufacturers warranty expires.
Likewise, a comprehensive plan from a top home warranty provider will also pay for repairs and even replace your washing machine when the time comes. For many homeowners, living without a washer and dryer is simply not possible.
Home warranty companies have networks of vetted technicians, so you do not have to worry about finding a trustworthy maintenance specialist. You simply call your provider, and they will schedule a service call.
You will be responsible for paying a service call fee, but after that, the company will pay for the remaining repair charges. After the repair is complete, most companies give you a 30 to 180-day reservice guarantee.
If the appliance breaks within the reservice period, you do not have to pay another deductible. These guarantees cover parts and labor, so you know you are not wasting money on repairs that do not fix the problem.
Plus, with an appliance warranty plan, you do not have to attempt DIY repairs and diagnostics. You can sit back and let a professional handle it for you.
Check The Machines Position On The Floor
Make sure the machine is set flat on the floor. Machines that are inclined or unbalanced are often programmed to stop functioning automatically to prevent them from falling over.
Check whether the machine is level with the floor or not. If its not, you might want to adjust its legs and make sure its secured in place.
Check Your Machines Inner Workings
If the hose drains when placed in the bucket, its time to check the machines inner workings for problems. This includes examining the drain pump, the lid switch, the belts and the water level control .
The drain pump is likely behind a panel that can be removed with a screwdriver. After you remove the drain pump, examine it for debris or obstructions and make sure the moving parts move freely. Sometimes simply cleaning the pump will do the trick. If nothing appears to be wrong with the pump, check to make sure all belts are in place and intact.
Find the lid switch and press it down while holding the lid open. The switch should click into place. If it doesnt, or if it seems loose, it may need replacing. Continue to check other parts of your machine. You may also find it helpful to look at the user manual.
The manual may have additional troubleshooting tips specific to your machine. Top load washers and front load washers have very different configurations, for example. If you dont feel comfortable messing with your machines insides, you might also call a washer repair technician at this point.