Whirlpool Washer Wont Drain To The Fullest
If you have set the load size for that particular load while the washer is in the middle of the cycle. There will be a slight, midway, or full fill of water in the washer. All items should be completely submerged in water, so that the tops are covered with water. Water should drain completely without a trace, not only partially, regardless of the size of the load.
If your Whirlpool washer wont drain completely, look at the drain hose for kinks or bends. It is also possible for the drain hose to become obstructed with small items, just like the drain pump. This can cause your washer to drain partially rather than completely.
Make sure your drain hose is free of kinks and bends once you have reached it. Make sure neither of these has caused wear or tears within the hose itself if you see them. You should also makesure the drain hose isnt higher than 96 inches off the floor, as if its too high, it wont drain. Since gravity cannot work well enough to drain the washer properly, water will remain in the drum.
How Do I Test The Drain Pump On A Whirlpool Washing Machine
Testing your machines drain pump is relatively easy. First, unplug the washer. Then, place several two-by-four blocks underneath the machines foot to keep the machines front elevated. If possible, ask for assistance.
Using a Phillips screwdriver, unscrew the screws located at the bottom of the panel. Once you remove the cover, youll find the drain pump directly in front of you. Prepare a bucket before turning the knob counterclockwise. The bucket will help you catch the remaining water inside it.
Place a gloved finger into the drain outlet and gently turn the impellers. If it doesnt turn freely, you might be dealing with a broken or a clogged drain pump.
Find The Drain Hose At The Back Of The Washing Machine
The drain hose resides behind your washer and connects the washing machine to your exterior washing machine drainpipe. If your drain hose is bent or has a kink, it may block the water flow. If this seems to be the issue, simply straighten the hose.
If it does not appear to have a bend or kink, your next step is to disconnect it from the washing machine drain. If necessary, unscrew the hose with a clamp attached. Always keep the hose higher than the washer tub until youre ready to empty out the water.
Read Also: My Sink Won T Drain But Isn T Clogged
Three: Access The Whirlpool Washers Drive Motor And Drive Belt
Tilt the machine and lay it down on its back use a buddy for safety. Use the 5/16 socket wrench to remove the screws attaching the belt guard. Then disconnect the drive motor wire connector and drive belt.
Note: This is a good time to inspect the drive belt. The belt may be busted or worn out, and you can simply replace it. A new drive belt costs between $5 and $15.
Wrong Whirlpool Wash Cycle Selected
Using the wrong setting for your particular load will leave clothes still wet after wash cycle ends. For example, the delicate or hand wash settings spin at slower speeds to protect more fragile fabrics. If these cycles are selected for a typical load of laundry, you may find the washing machine isnt spinning sufficiently, leaving clothes wet.
Always check your washer settings and clothing tags before starting your machine to ensure youve selected the right cycle for your laundry.
Also Check: Bathtub Won’t Drain At All
The Truth Is That There Are Quite A Bit Of Causes Why A Whirlpool Washer Wont Drain
If you were to open the lid or door of your Whirlpool washer mid-cycle, you would notice a large amount of water submerging your laundry items. With agitation motions, this water works with your detergent to remove all the dirt and grime from your clothes. If your washer does not drain the dirty water immediately after this process, what should you do?
It is possible that the clogged pump in your Whirlpool washer could be the reason your washer wont drain. As a result of small items falling out of clothing, your washer can hold water due to a clogged drain. Ensure your washing machines drain pump is not obstructed by any objects by removing it.
Be sure to carefully remove any objects that are obstructing your Whirlpool washers drain pump after removing the drain pump. The pump should not be obstructed if nothing is blocking it. However, if the drain looks very worn, it may merely be a matter of replacing the drain pump. Your washer will drain more effectively at the end of the cycle if you have a newer pump.
Reasons Why Whirlpool Washer Not Spinning
When the Whirlpool Washer Not spinning, its a painful loss of time to check each possible cause. Piles of wet laundry on our floor are what prompts people to Google why wont my washer spin or Why doesnt my washing machine spin? But they dont need to waste valuable time searching for an explanation.
Let us help you troubleshoot your washer so that you can focus on your life.
Recommended Reading: How To Drain Middle Ear Fluid At Home
What To Do When Your Whirlpool Washer Wont Drain
When a Whirlpool washing machine wont drain, the issue can be due to several reasons. While minor clogs may require nothing more than a plunger, more serious problems may be related to faulty mechanical parts. Depending on the source of the problem, there are many different fixes that you can try at home.
Is your Whirlpool washer on the fritz? You cant get it to drain and youre afraid that it wont clean your clothes as well. First, check the drain hose. It might have a clog in it. Clear the drain hose of any obstructions. If that doesnt work, try using a plunger to dislodge whatever is stuck in the drain hose.
Does The Drain Pump Filter Have A Blockage
Many washers have a drain pump filter or coin trap that collects dirt, lint and debris to prevent it from clogging the drain pump. If the filter is blocked by these remnants, it wont drain properly and needs to be cleaned for water to drain.
Most drain pump filters can be accessed through a small door on the bottom right corner of the washer. Remove the filter, dispose of any debris and rinse it under running water before replacing it. If you still find your Whirlpool washer not draining and suspect drain pump issues, a professional technician should assess the pump for clogs or malfunctions.
Recommended Reading: 20 Gallon Portable Oil Lift Drain
Why Is My Whirlpool Washer Not Draining Lets Fix It
Your washing machine will break down from time to time, and thats just a fact of life. It can be frustrating to run into issues with your Whirlpool washing machine when its in the middle of its cycle. Luckily, there are a few things you can check before calling a plumber out. This article will help you figure out why you are facing Whirlpool Washer not draining problem, using simple explanations for common causes of washing machine drainage problems.
Washing clothes without a care in the world is a luxury and one you shouldnt take for granted. Your washer should work as well as possible and should be easy to fix.
At the end of each cycle, its crucial for your Whirlpool washer to drain all of the water from its drum. This prevents clothes from being wet at the end of a wash cycle, which can cause them to mildew or smell bad. Here are the steps to take if youve noticed that your Whirlpool washer is leaving some water behind after its cycles.
A Clog Has Been Detected In The Whirlpool Washer Drain
Technology inside many Whirlpool washers makes it possible to detect what is wrong without you having to investigate on your own. Whirlpools features include alerting you when a drain clog is detected. You may wonder if a repairman is needed if you receive this message. However, take a look at the instructions below for a possible solution to Whielpool washer wont drain properly.
Whenever your Whirlpool washer senses a clog, disconnect it and raise it from the front, placing two-by-four blocks under each foot. The drain pump can be accessed by unscrewing three screws at the base of the panel.
Remove the drain pumps knob with a Phillips screwdriver while holding a bucket underneath to catch any excess water. Once the knob has been turned over, you will see the filter on the back. Plug the pump back in, replace the drain filter, screw on the cover, and remove the blocks.
Recommended Reading: My Bathtub Won’t Drain
How To Drain A Washing Machine Manually
If your washing machine is not draining completely, the mechanics of draining the water is up to you. Here are a few ways to manually drain the water in your washing machine:
-
Bail it out with a bucket: Bailing out the water with a bucket, cup, or bowl is often the go-to strategy for most people who find that their washing machine wont drain. However, this technique can be time-consuming, tedious, and hard on your back because you have to bend over repeatedly to scoop up water from the bottom of the machine.
-
Drain it with a hose: This is an easier way to drain water than bailing it out with a bucket because youre using the drain hose and letting gravity do the hard work for you. To drain your washer with the washing machine drain hose, youll need a bucket, a screwdriver, needle-nose pliers, and a clamp. Its also a good idea to have a sponge and towels on hand in case of a spill.
Follow these steps to drain the water with the drain hose.
Whirlpool Washer Drain Clog Detected
The great part of the technology behind many Whirlpool washers is that they can often indicate what is wrong with the machine without you ever having to investigate on your own. One of these features is a Whirlpools ability to notify you when a drain clog is detected. If you get this message, you may be wondering if a repairman is needed, but take a look below to see how to potentially resolve this problem without having to call in the professionals.
If your Whirlpool washer sensing light indicates that a drain clog is detected, unplug the unit and lift it from the front, placing two-by-four blocks under each foot. You will then unscrew three screws at the bottom of the panel, remove it, and the drain pump will be in front of you.
Once you see the drain pump right in the middle of the machine, use a Phillips screwdriver to take off the knob on the drain pump while holding a bucket beneath it to catch any excess water. You will then turn the knob over to expose the filter on the back. Remove any debris and replace the drain filter back onto the pump, screw on the cover, take away the blocks, and plug it back in.
Read Also: Why Is My Basement Drain Backing Up
Whirlpool Washer Wont Drain
Categories Home and Kitchen, Washer & Dryer, Whirlpool Washer
Although proper agitation and cleansing of loads is the main goal of any Whirlpool washer, just as important is its ability to drain all of the water in which your load was cleaned. If you notice that your Whirlpool washer is suddenly no longer draining, what is the cause?
If your Whirlpool washer wont drain, it could be caused by a clogged drain pump, kinked drain hose, faulty lid switch, or a clogged coin trap. To resolve these issues, it is possible to partially disassemble your washer on your own and unclog or replace any problematic areas.
Being able to wash items without having to think twice is a luxury many forget is such, that is until their washer is suddenly not working as it should. At the end of every cycle, your Whirlpool washer should drain all of the water from its drum, which allows the clothes to be spun so they are made rid of any excess water and allows them to dry properly after the washing process. Continue reading to figure out why your Whirlpool washer wont drain.
Drain Hose Is Kinked Or Clogged
A kinked or clogged drain hose is one of the most common reasons for a Whirlpool washer not draining. Kinks can occur if the washer moves or pushes the hose up against the wall. This twist in the hose restricts the flow of water, causing it to back up into the washer. While you may be able to gently straighten the hose to remove the kink, the hose must be replaced if damaged.
Clogs often occur if debris or a small article of clothing causes a blockage in the hose. Consult your user manual for specific instructions on how to disconnect the hose from your model washer and inspect it for clogs.
Once the hose is disconnected, follow these steps to remove the blockage:
- Allow the hose to drain any residual water into a bucket or sink.
- Carefully remove the obstruction with tweezers or a straightened wire hanger.
- If the blockage isnt visible, the hose must also be disconnected from the standpipe or sink for inspection.
- Replace the hose if the blockage cant be reached.
You May Like: Is Thrift Drain Cleaner Safe For Septic Systems
Consult The User Manual
Refer to the troubleshooting guide in the user manual. If the machine is showing an error code, check what the manual says about it. For example, F21 error code means that the drain filter on the drain pump or the drain hose is clogged. , you will need the model number, which you can find beneath the washer lid, on the tub rim.
Inspect The Washing Machine Drain Pump
The next step is to check the washer pump to see if it has a clog, a broken belt or impeller , or a leak. Read through the washing machine manufacturer instructions, which should include a diagram of your units drain pump location and components.
Usually, if the drain pump isnt working properly, youll hear an unusual noise or notice leaking from the washing machinewhen it is running. If your pump is malfunctioning, youll need to replace it yourself or call a professional to replace it for you. If you do replace it yourself, make sure to purchase the same pump model so that it properly fits your washing machine.
Also Check: How To Unclog The Shower Drain
How Do You Fix A Whirlpool Washer That Wont Start
To fix a Whirlpool washer that wont start, there are several steps that should be taken. First, check the power cord and make sure it is securely plugged into the electrical outlet. If it is securely plugged in, the next step is to check the circuit breaker and reset it if necessary.
If the circuit breaker is not the issue, remove the top panel of the washing machine and check the lid switch. This is typically located on the inside of the washer near the door. Make sure the lid switch is fully secured in the catch and the plastic tab is not broken.
If the lid switch is not working, it may need to be replaced.
Once the lid switch is working, check the drive belt that connects the motor to the transmission. If this belt is broken, you will need to replace it. Disconnect the power before attempting any repairs on the belt or motor.
If the drive belt and motor are functioning properly, the timer may have gone bad or have a bad connection. The timer is located on the control panel and is responsible for advancing through the various cycles.
Replace the timer if needed and check the wiring connections.
If none of the above issues are the cause of the washer not starting, it may be due to a bad motor coupling. To replace the motor coupling, pull the washer away from the wall and remove the back panel.
Detach the motor from the coupler and replace with a new one.
Is The Lid Open
If the lid is lifted during a cycle, the machine will stop. To continue the cycle, close the lid and you may have to select the Start button again. The lid must be closed during operation for the washer to fill with water, and then to wash, drain, rinse and spin.
Watch the below video for more information on proper drain hose installation.
If you would like to download or view product literature for your appliance, please visit our Manuals and Literature page.
Don’t Miss: Home Depot Dishwasher Drain Hose
New Whirlpool Washer Not Draining
Did you just purchase a brand new Whirlpool washer and it is not draining water? Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also cause your new washer not to drain.
Likewise, the hose may be jammed as simple as that sounds its worth checking it out. Whatever might be the cause, you need to drain the water from the washing machine before any work or diagnosis can be performed.
Then you can follow the guideline below to resolve the issue without consulting the professionals yet:
- Ensure that the drain hose is not kinked or clogged.
- Straighten the hose for easy flow of water.
- Remove any material obstructing the drain hose, drain pipe, or utility sink.
- Make use of the U-shaped drain hose form on the drain hose, and secure the drain hose.
This should fix the issue of the new Whirlpool washer not draining.