Blocked Drain Pump Filter Or Hose
A blocked filter or hose can prevent your Samsung washer from draining water, which can cause it not to spin.
A drain pump filter protects the pump from a build-up of lint and other things that can cause obstruction. If the drain pump filter is blocked, water will not be able to drain to the pump, which can cause standing water and keep your washer from spinning.
A drain hose moves dirty water out of the washing machine and into the sewer system at the end of each cycle. If the drain hose is blocked, water will not be able to drain, which can cause your Samsung washer to not spin.
To prevent water damage to your home or damage to the washer, contact a professional to clear blockages.
Tub Seal And Bearing Kit
The tub seal and bearing kit helps to keep the water in the washer from leaking out. The kit includes a new tub seal and two bearings.
Why does it fail?
The bearings and seal can wear out over time, causing the washer to leak water.
How do you know its failed?
If your washer is leaking water, it is likely that the tub seal and bearing kit has failed.
How to fix it?
-Pry bar
Instructions:
Before you begin, make sure that you have all of the tools and parts that you will need. Once you have everything, follow these steps to replace the tub seal and bearing kit.
-Using a Phillips head screwdriver, remove the screws from the back panel of the washer.
-Remove the back panel and set it aside.
-Locate the tub seal. It is a ring of rubber that sits between the tub and the back panel.
-Using a flathead screwdriver, pry the old tub seal out.
-Take the new tub seal and place it into position.
-Using a socket wrench, tighten the bolts that hold the tub in place.
-Replace the back panel and screw it into place.
-Locate the bearings. There are two of them, and they sit on either side of the tub.
-Using a hammer, tap on the old bearings until they come loose.
-Remove the old bearings and insert the new ones.
Rear Drum With Bearing
The rear drum is the part of the washer that holds the clothes during the wash cycle. The bearing is what allows the drum to spin freely. If your washer is not spinning, it could be because the bearing has failed.
To check if this is the problem, remove the back panel of your washer and take a look at the rear drum. If you see any damage to the bearing, then that is likely the problem.
To fix this, you will need to replace the rear drum and bearing assembly. This is a relatively easy repair that you can do yourself.
To replace the rear drum and bearing:
-First, remove the back panel of your washer.
-Then, remove the retaining ring that holds the drum in place.
-Next, take out the old drum and bearing assembly.
-Now, install the new rear drum and bearing assembly.
-Finally, replace the back panel and youre done!
You May Like: Home Depot Rent Drain Snake
One Simple Protection Plan For Your Home’s Major Appliances
Forget what you know about warranties, Asurion Appliance+ is so much more. Cover all your eligible appliancesâno matter where you bought themâand get 24/7/365 troubleshooting support, all for less than $1 per day. Learn more about Asurion Appliance+ coverage and how you can get total peace-of-mind protection.
Appliances aren’t cheap
Neither are their repairs. But Asurion Appliance+ can save you money every month and provide some peace of mind.
Diagnostic On Samsung Top Load Washer Not Spinning Clothes Dry
Option 1
It takes these steps to put your Samsung top loading machine on diagnostic mode:
- Keep the washer plugged into the power
- Press Power to turn the washer on
- Then press the Temp switch and hold it until the indicator LEDs turn on
- Wait to view error codes
Option 2
- Plug your washer into the power
- Press Delay and hold it until number 17 shows up on the display panel
- Now press the Star switch for 7-10 seconds
- Then press Self-Clean to display CR
- Turn the Wash Cycle knob clockwise to view the error code
Don’t Miss: Water Backup Of Sewers Or Drains
Diagnostic On Samsung Front Load Washer Not Spinning Clothes Dry
It takes these steps to put your Samsung front loader on diagnostic mode:
- Plug the washer into the power
- Press Power to light up the LEDs
- Then press Delay + Soil Level to display 0000
- Press Spin to display the letter D, showing you are on diagnostic mode
- Wait to view the error code
Note: Check out what the error code means on Samsungs official page
Samsung Front Load Washer Not Spinning Fast Enough
If your Samsung front load washer is not spinning fast enough, there could be a few different reasons why. First, make sure that nothing is blocking the washers spin basket or tub.
If any clothes or other items are obstructing the spinning mechanism, this could be causing the issue.
Additionally, check to see if the washers spin cycle is set to the correct speed. If it is set too low, this could also be contributing to the problem.
There are a few different solutions you can try if your Samsung front load washer is not spinning fast enough.
First, you can try running the washer on a higher spin cycle setting. If this does not work, you may need to clean the washers filters or other components.
Additionally, if the issue persists, you may need to contact a Samsung customer service representative for assistance.
Related:
Also Check: 25 Ft Drain Snake With Drill Attachment
Damaged Or Broken Drive Belt
The drive belt encircles the washer tub via two pulleys and rotates the tub via the motors power. Over time, this thin rubber belt can fray, loosen or break. When this happens, youll find your Samsung washing machine not spinning smoothly, quietly, or, if the belt is broken, not spinning at all. If inspection of the drive belt shows damage like fraying, loosening, or breakage, it must be replaced.
Samsung Washer Wont Drain Heres What To Do
If your washer wont drain, you cant use it its that simple. There are many different reasons why your washer might not be draining, and fortunately, it can often be a very simple problem to fix.
This guide will explain the most common reasons why your Samsung washer refuses to drain after a wash cycle and provide some simple solutions you can try to fix the problem.
The following models of Samsung washer are covered by this guide:
592-49045
WF350ANWXAA
Also Check: Ge Washing Machine Drain Pump
The Load Isn’t Balanced Properly
If you’re trying to wash only a couple of heavy items, your washing machine may not spin or may not spin effectively. This often occurs when you’re washing things like a comforter or shoes. Open the machine and shift the items around to balance the washing machine load, and your washer can spin more effectively. Adding more items to help balance a load can be effective, too, as long it doesn’t overfill the machine.
What To Do If Your Samsung Washing Machine Is Not Spinning
There are several reasons which may explain why the spin performance of your washing machine does not complete as expected. Sometimes it can be because there are sensors in the machine which slow or stop the spin cycle automatically if it detects an issue. Use the guide below to help determine the possible reasons that can cause this issue and what you can do to try to resolve them.
For more information about your appliance consult your user manual.
Don’t Miss: Crawl Space French Drain Installation
Washer Stops During Spin Cycle
Problem: Washer stops during the spin cycle and becomes off-balance. The spin cycle will complete after clothes are rearranged.
Solution:
- Run a diagnostic test to see if any error codes appear. The failure to complete the spin cycle can be caused by a slow drain and that code will appear.
- To correct the slow drain, open the bottom panel of the washer housing. You will see a plug on the lower right. Have some towels ready to catch a gush of water and remove the plug. Clean out the filter. You may find lint, coins or buttons are obstructing the flow into the pump.
- Never overload the washer. Take time to read the manual when you are not in a hurry to learn which cycle to select for different size loads.
Drum Not Turning At All Click To Expand
If the drum doesnt turn at all during the wash cycle and the spin cycle, then this issue will likely require an engineer. To check this, you will need to run a short cycle, with no washing and no detergent. When the cycle has started, you will need to watch the drum. During the initial few minutes, the unit will fill with water, after this has happened you will need to look through the door to see if you can see the drum rotating. It is normal for it to stop and start a few times. If the drum is still not turning, you can request a repair.
If your Samsung washing machine does not spin as expected during the rinsing or spinning phase of the cycle, it is most likely caused by an unbalanced load.
One sign that your load might be unbalanced is if the cycle time is sticking and pausing for extended periods of time .
This video helps to explain:
If a load unbalance is sensed during the start of a spin cycle or during a rinse cycle, the machine will attempt to automatically reposition the load by rotating slowly in both directions.
The auto-redistribution will happen multiple times depending on the cycle chosen and can extend the overall time by 30 minutes for particularly uneven loads.
If the washing machine decides the load is within safe limits and can be spun but at a slower speed, it will automatically adjust the final spin speed and complete. This is why the result can vary between loads and cycles.
Follow these steps to manually adjust your load:
Start the cycle again.
Read Also: Something Is Draining My Car Battery
How Do I Clean The Debris Filter
You can locate the debris filter in the lower back portion of the wash drum. The manufacturer recommends that users clean the filter a minimum of 3 times a year. Generally, your machine will display a 5E error code if there is a clogged filter.
Its super easy to clean the top load washer filter. Unclip the filter from inside the drum and rinse it with a high-pressure nozzle. Once you clean the filter thoroughly, clip the filter back into the drum. Make sure you clean out the filter holder before you do it for maximum benefit.
How Will I Know If My Washer Has Stopped Spinning
The most obvious sign that your washer has stopped spinning is hearing loud banging sounds coming from the machine. This is the first alert of an unbalanced load. Rearranging the clothes in the wash drum will correct the problem here.
If the machine stopping does not involve the clothes distribution, it could be another cause. When looking at the control panel, is your top-loading Samsung washing machine displaying a UE, UL, or dC error code? If yes, this means there may be a mechanical issue to troubleshoot, and a part may need repair.
Don’t Miss: Where Can I Buy Thrift Drain Cleaner
Move The Washer To A More Even Surface
One primary reason for load imbalance is an uneven surface. If your Samsung washer seats on a non-uniform surface, the load will fall out of balance.
Once that happens, it becomes harder for the laundry to spin correctly and spin-dry at the end of the cycle.
If your washer stands on an uneven surface, move it to a more even surface. If thats not possible, adjust its leveling legs until its stable.
After that, examine the wash load and rearrange it if its out of position. Ensure you evenly distribute the clothes in the drum.
Examine The Drive Belt For Fault
Your washing machine has only one drive belt. If its faulty, then it wont spin properly or may fail to do it entirely.
Overall, inspect your washing machines drive belt for the following faults:
- Excessive stretching
Replace your washers drive belt if it looks loose, cracked, or frail, as those are faulty signs.
You May Like: Unclog Bathtub Drain With Baking Soda And Vinegar
Have You Tried Turning It Off And Back On Again
Okay, that headline was a bit of a misleading question, but I couldnt resist. Samsung washers are software-heavy devices. meaning the program that allows them to function could simply have crashed.
To restart the program, you do indeed need to turn the machine off and back on again with a hard reset . To do this, simply:
This allows the internal memory to clear and gives it a chance to wake up so to speak, clearing any old bits of code that were hindering the machine from working.
How Do I Fix Clogged Or Damaged Hoses
A clogged or damaged hose requires more effort but is still pretty simple to fix. Disconnect the hose by unscrewing and unclamping from the machine. Check the hose for damage or blockage.
If the blockage isnt too deep, you can clear a clogged hose with needle-nosed pliers. However, a blockage thats deeper into the hose or a damaged hose will need replacing.
You will need a new hose, a Phillips screwdriver, and pliers to replace the washer hose. Unscrew the clamp at the top of the hose connected to the washer. Use pliers to move the metal clamp from the bottom of the hose and remove.
Transfer the metal clamp onto the new hose, then snap the bottom end of the hose onto the washer. Move the metal clamp down into place between the thread lines. Feed the hose into the top clamp and screw it back into the washer. Finally, attach the top end of the hose to the drain.
Don’t Miss: Baking Soda Vinegar To Clean Drain
Washing Machine Isnt Level
Whats one of the most common causes for a Samsung washer not draining? A machine thats not level will cause draining problems and can also be responsible when your washer wont spin properly. If a leveling tool reveals that your machine isnt level, first check the floor underneath the washer. Carpeting or a slippery surface can make the floor uneven or cause rocking.
If the floor is level and the machine can still rock back and forth, check the washers leveling feet to make sure theyre even. Rotate the leveling feet counterclockwise to lower them and clockwise to raise them until theyre even.
Is Your Washer Still Not Spinning
Our washer repair experts will solve any issue with your broken appliance.
With proper use, care and maintenance of your top-load or front-load washing machine, you should experience many trouble-free years of operation. If you encounter problems with your washer not spinning or other issues, contact FIX Appliances CA online or by calling 1-888-242-0777.
You May Like: How To Clean Bathroom Sink Drain Smell
Check Your Laundry Load
Two issues with your wash load could prevent it from spin-drying, and they are:
Lets start with the first one.
If the laundry load is uneven or out of balance, the heavy side will weigh the washer down, preventing it from spinning correctly or spinning at all. Consequently, youll have wet clothes once the cycle completes or when the washer stops mid-cycle.
How about excess laundry?
Well, excess laundry also weighs down the washing machine. The laundry cannot spin properly and may also fail to turn entirely, causing wet clothes in the end or when it halts mid-cycle.
Remember, the recommended load capacity is ¾ full. Anything above that equals an overload.
Distribute your clothes evenly in the washer drum if they are out of balance. It may mean adding a few clothes or removing the bulky ones to even out the load.
And if the load is more than ¾ full, you should reduce it. Avoid overloading the washer, but dont underload it either, as it may not spin.
Drain Hose Is Clogged Or Pinched
Clogs, kinks and improper drain hose installation can also cause draining problems, as they prevent water from flowing through the hose.
Follow these steps to assess the drain hose:
Recommended Reading: How To Get Rid Of Fruit Flies In The Drain
Door Lock Motor And Switch Assembly
A faulty door latch can prevent your clothes washer from spinning. You can take the washer door apart, but its easier to use a multimeter to test the door latch. If the door latch is not functioning or is broken, it will prevent the washer from operating properly. If this defect occurs, a consumer will not be able to use the washer. These issues could happen mechanically or electrically.
The washers door latch will open and close the front of the washer door. When the door is closed, it will secure the washers mechanical components motor and gears inside. If there is a failure in the door latch mechanism, it can stop the washers operation. If there is a defect in the door latch, it will not secure the washer door shut when in use.
What can you inspect in the case of a faulty door latch? First, inspect whether or not the latch is damaged. Next, check for any signs of electrical issues by checking to see if there is continuity between any of the door latchs electrical switches. This will warn you if anything is corroded and in need of replacement. Finally, if there are no problems but the door latch simply doesnt function, replace it.