Tuesday, December 5, 2023
HomeNewsTop Load Washer Not Draining

Top Load Washer Not Draining

Kinked Or Blocked Drain Hose

Top-Load Washer Wont Drain Washing Machine Troubleshooting

If the washer will not drain, the drain hose may be kinked, pinched, or obstructed by a small object. If you are unable to straighten the hose or clear an obstruction, you will need to replace the hose. Also check the height. Whirlpool advises that the height of the drain hose should not exceed 96 inches, as this will cause water to flow back into the tub.

The drain hose can be checked for a blockage by disconnecting it from the washer at the rear of the machine. On most models, it can be unscrewed, or pliers can be used to remove the clamp that secures it. The hose can be unblocked with a drain snake tool and washed with a mixture of hot water, white vinegar, and baking soda. The washers internal drain hose can also be checked by following the drain pump instructions below.

Was A Gentle Or Delicate Cycle Or Low Spin Speed Selected

Gentle cycles, such as gentle, delicate, or handwash, use slow spins to keep fabrics from stretching and wrinkling. Slow spinning also leaves more water in the load. To remove more water, select a cycle that uses high spin speeds. A cycle or fabric selection such heavy duty or super has higher spin speeds and will leave less water in loads. Always follow your clothing care label to determine what cycle to use that is best for the garments being washed.

Kenmore Washer Not Draining Or Spinning

Generally, Kenmore is considered a popular appliance brand that manufactures front load, top load, and twin load washers. Usually, if the Kenmore washer wont spin or drain, it could be because the pump is damaged or something is stuck in the washing machine drain hose or pump.

In some cases, you may notice that the Kenmore washer is not spinning or draining properly.

If the Kenmore washer does not drain or spin, you need to check the washing machine, drain hose, or pump because something might be stuck in there or this pump might be broken.

So, there could be some other reasons behind the Kenmore washing machine not raining or spinning. Below is a brief discussion on a few reasons why different types of Kenmore washer does not spin or drain:

Recommended Reading: How To Drain Ac System

What To Check When Your Top Load Washer Will Not Drain

There are few more heartbreaking appliance issues than opening your washer after the cycle is supposed to be done and finding that your clothes are still sitting in a tub of water. While you can certainly pull your clothes out and wring the excess water out of them, you still have all that water in the machine to deal with. It isnt going away and if you let it sit, it is going to get nasty in there pretty quickly.

However, a tub full of water isnt the end of the world. In fact, if you know what to check, it can be fixed very quickly, depending on the problem. Once you do fix the problem, however, you will definitely want to rewash that load of laundry just to make sure it is both rinsed of washing detergent, but also that they are actually clean.

Removing Water From A Washer

Top 10 Front Load Washer Not Draining

After you have done your initial troubleshooting above, now is the time when you can give in to that impulse to drain your washer. To check for deeper clogs or other issues, you will need the washer free of water to avoid making a mess. Start by unplugging your washer if you have not already. If you have a shop vac that does wet work, you can use that to drain your washer.

Unfortunately, if you do not have access to a shop vac that allows for water suction, you will have to do it the old fashioned way, which is bailing out the water with a small bucket and soaking up whatever remains with a few towels.

Also Check: Brushed Nickel Tub Drain Cover

Possible Causes Of Why Washer Is Not Draining Water

Before getting into the steps of solving the problem, its important to first understand why your washing machine drain system might malfunction. Among the many possible reasons this might happen are the following:

Some of these causes are easier to check for than others. In general, its best to follow a systematic process to check for and resolve the issue, as described in the next section.

Is The Drain Hose Kinked Or Is The Drain Clogged

Make sure that the drain hose is not kinked or clogged. Straighten the hose for adequate water flow. Remove any blockage from the drain hose, drainpipe or utility sink. Use the U-shaped drain hose form on the drain hose, and secure the drain hose. See the Installation Instructions for further details.

Read Also: Fiberglass Shower Drain Removal Tool

What Causes A Washing Machine To Not Spin Or Drain

Opening the washing machine lid or door after the end of the wash cycle and discovering your clothes are still submerged underwater can really dampen your spirits. Before you invest in a vintage hand-cranked laundry wringer to squeeze out that water, you should troubleshoot the likely causes of the washer failing to drain or spin . The solution to the problem can be quite simple, and the appliance replacement part you need can be relatively inexpensive and easy to install.

The reasons a washer will fail to drain, or spin, will differ depending on whether you own a top-load model or a front-load model. Lets examine how each washer type handles these two cycles

How To Drain Water Manually

Washer Troubleshooting: Top-Load Washer Won’t Drain – How to Fix Your Washer | PartSelect.com

It may be necessary to first drain any remaining water to avoid a mess during your Samsung washing machine troubleshooting. However, opening the washer door and attempting to mop up the water can still result in a messy cleanup.

Heres how to drain water from Samsung washing machine manually before troubleshooting:

  • Unplug the washing machine.
  • Also Check: Bathtub Drain Leaking Through Ceiling

    When To Call A Professional

    If youve gone through the steps to troubleshoot your washing machine issue and still cant find the reason, there may be a bigger problem at play. On average, professional services cost $150 to $300 for a machine that wont drain and$150 to $500 for a machine that wont spin.

    Compare Quotes From Top-rated Local Plumbers

    Free, No-commitment Estimates

    Drain Hose Is Clogged Or Pinched

    Clogs, kinks and improper drain hose installation can also cause draining problems, as they prevent water from flowing through the hose.

    Follow these steps to assess the drain hose:

  • Inspect the hose for kinks or damage. While some kinks can be gently straightened, a damaged hose requires replacement.
  • Check your user manual to determine how to disconnect the hose and assess for clogs. Remove any visible blockages before reconnecting.
  • Make sure the hose is properly installed. The hose should descend 6-8 inches down the standpipe or sink without forming an airtight connection. It should also be 18-96 inches in height.
  • Also Check: Clean Shower Drain With Baking Soda And Vinegar

    Cause : Faulty Pump Motor

    If you have removed any clogs from the washing machines waste hose and drain pump and the machine still will not drain water, there might be a problem with the pump motor. The washing machines motor provides the drain pump with the power to drain the basin. Find a replacement motor for your Kenmore washing machine from this website and use the Kenmore 110 Series Washing Machine transmission, motor, and pump diagram to replace the faulty motor.

    Faulty Door Lock And Switch Assembly

    Top 8 Recommended Frigidaire Front Load Washer Not Draining  Home ...

    If the control panel is flashing an LG washer OE error code its often due to a problem with the machines door lock and switch assembly. This mechanism senses when the door is closed and signals the machine to begin a wash cycle. If the lock is broken or the switch is faulty, the machine wont receive the signal to operate and the washer will not spin, drain or even start.

    A malfunctioning door lock and switch assembly cannot be repaired and should be replaced.

    We hope this guide saved you some valuable troubleshooting time when an LG washer wont drain. If your troubleshooting reveals the need for a washer repair, Same Day Service Company can save even more time with a fast and expert repair. Call us today so you can continue to wash, dry, fold, repeat!

    Recommended Reading: My Dishwasher Isn’t Draining

    Cause : Clogged Drain Pump

    If your washing machines waste hose is cleared of any clogs and it is still not draining properly, your machine may have a faulty drain pump. Because the drain pump has a translucent cover, a clog may be visible in the pump without having to take it apart. If you see a clog, use the Kenmore 110 Series Washing Machine Water Pump Replacement Guide to remove the machines water pump.

    A Damaged Or Worn Belt

    If the drain pump is not damaged or clogged by the water still does not seem to be draining during the wash or rinse cycles, your washing machines drive belt might be damaged. The drive belt is what operates the pump and is located at the bottom of the washer. Heres how you can replace it.

    If your washing machine is having trouble spinning, there might be something wrong with its belt. Contact the manufacturer to order a replacement drive belt. The process of replacing it should be simple, but you will need to remove the back access panel first so that you can get to the drive belt.

    Unplug the washer, remove the access panel, and lower the tub until it locks into place. Examine the belt for wear and tear or any notable imperfections. Replace if needed.

    Read Also: How To Fix Clogged Ac Drain Line

    Check Your Machines Inner Workings

    If the hose drains when placed in the bucket, its time to check the machines inner workings for problems. This includes examining the drain pump, the lid switch, the belts and the water level control .

    The drain pump is likely behind a panel that can be removed with a screwdriver. After you remove the drain pump, examine it for debris or obstructions and make sure the moving parts move freely. Sometimes simply cleaning the pump will do the trick. If nothing appears to be wrong with the pump, check to make sure all belts are in place and intact.

    Find the lid switch and press it down while holding the lid open. The switch should click into place. If it doesnt, or if it seems loose, it may need replacing. Continue to check other parts of your machine. You may also find it helpful to look at the user manual.

    The manual may have additional troubleshooting tips specific to your machine. Top load washers and front load washers have very different configurations, for example. If you dont feel comfortable messing with your machines insides, you might also call a washer repair technician at this point.

    Is The Drain Hose Installed Correctly

    GE Top Load Washer Won’t Drain

    Verify that the drain hose is not too far down into the standpipe beyond the elbow which could cause siphoning, water to drain back into the tub or slow or no spin. The way the drain hose comes from the manufacturer is correct for standpipe or wash tub installation. The drain hose form SHOULD NOT be altered for standpipe or wash tub installation. Do not tape the drain hose to the drain pipe.

    for more information on the Drain Hose installation

    Don’t Miss: Schluter Kerdi-drain Grate Kit 4 Oil Rubbed Bronze

    Why Is My Samsung Washer Not Draining Water

    When your Samsung washer doesnt drain, it can be alarming to find your clothes sitting in water in the wash tub. What causes draining problems? It could be because the washer isnt level or the drain tube is clogged or pinched. Adjust the legs of your washer, as needed, and check the drain tube for kinks or damage. Troubleshoot a Samsung washer not draining with these likely causes and straightforward solutions.

    Reset The Washing Machine

    When the washer stops draining, it can be due to an internal error code or control panel malfunction. Resetting the machine to factory settings can resolve issues like these and get the washer working again.

    Make sure to read your household appliances manual before trying anything else! Many modern washers have a reset button that you can access by pressing the panels buttons. Older top-loading washer models require you to unplug the device for one minute, then plug it back in.

    You May Like: Kitchen Sink Drains Slow And Gurgles

    Drain The Washer Manually

    If your front load washing machine will not drain water, you may need to drain it manually. To do this, unplug the washing machine from the power outlet and remove the hose from the back of the washer.

    Place a bucket underneath the hose and open the valve to allow the water to drain into the bucket. Once all of the water has been drained, replace the hose and plug the washing machine back in.

    Drain Hose Is Kinked Or Clogged

    Samsung Top Load Washer Not Spinning Or Draining

    A kinked or clogged drain hose is one of the most common reasons for a Whirlpool washer not draining. Kinks can occur if the washer moves or pushes the hose up against the wall. This twist in the hose restricts the flow of water, causing it to back up into the washer. While you may be able to gently straighten the hose to remove the kink, the hose must be replaced if damaged.

    Clogs often occur if debris or a small article of clothing causes a blockage in the hose. Consult your user manual for specific instructions on how to disconnect the hose from your model washer and inspect it for clogs.

    Once the hose is disconnected, follow these steps to remove the blockage:

    • Allow the hose to drain any residual water into a bucket or sink.
    • Carefully remove the obstruction with tweezers or a straightened wire hanger.
    • If the blockage isnt visible, the hose must also be disconnected from the standpipe or sink for inspection.
    • Replace the hose if the blockage cant be reached.

    Recommended Reading: How To Drain Dog Anus Glands

    Drain Manually If Needed

    If you have deduced that the issue is most likely still a clog in the drain hose that you were unable to easily access, you will need to remove the drain hose from the machine to thoroughly inspect it.

    Before doing this, however, you need to manually empty your machine. Otherwise, the water will spill out when you disconnect the hose. While an unpleasant process, the mess can be kept to a minimum if you make use of buckets and towels.

    Whirlpool Front Load Washer Wont Drain Or Spin

    What to do when your Whirlpool Front Load washer wont drain, spins slowly or leaves wet loads:

    If you have selected the Delicate or Handwash cycle, you must change the cycle to a regular wash. If the problem continues, turn off the power at the breaker or fuse box and check for a kinked drain hose or clogged drain. Make sure that hose is more than 96 above the floor and is not coiled.

    Dont let a clogged drain pump, kinked drain hose, faulty lid switch, or a clogged coin trap ruin your fun. If you have any issues with your Whirlpool washer not draining properly, dont panic. With just some basic tools, its easy to partially disassemble your washer and replace any of its faulty components.

    You May Like: Pull Hair Out Of Drain

    Is The Drain Hose Too High

    Make sure that the drain hose does not extend more than 5″ into the Standpipe or laundry tub . Using the U-shape drain hose form , will provide the correct length of drain hose in the drainpipe or laundry tub.

    The drain hose cannot extend higher than 96″ from the floor.

    Do not tape the drain hose to the drain pipe.

    Wrong Whirlpool Wash Cycle Selected


    Using the wrong setting for your particular load will leave clothes still wet after wash cycle ends. For example, the delicate or hand wash settings spin at slower speeds to protect more fragile fabrics. If these cycles are selected for a typical load of laundry, you may find the washing machine isnt spinning sufficiently, leaving clothes wet.

    Always check your washer settings and clothing tags before starting your machine to ensure youve selected the right cycle for your laundry.

    Also Check: How To Clear Clogged Drain Pipe

    Drain Pump Guard Filter

    Some Electrolux models feature a drain pump filter. It is usually located behind a small panel at the bottom right of the machine. You should be able to open the panel with your fingers or a flathead screwdriver. Before unscrewing the filter, make sure to put a towel down. You will also need a container to collect the water that comes out.

  • Open the pump guard panel.
  • Pull the emergency hose out.
  • Place the hose in a container and remove its cap.
  • Unscrew the pump guard filter.
  • Wash the filter in the sink to clean it.
  • With the filter out, check the pump impeller. Rotating it should release any debris that is stuck.
  • Put the pump guard filter and emergency hose back into the machine.
  • Clogged Drain Pump Or Drain Pump Filter

    Most front load washers have a drain pump filter to prevent lint and foreign objects from clogging the drain pump. However, the filter can become blocked with these items, causing any draining water to back up into the washer. Regular cleaning of the drain pump filter can prevent clogs and ensure the washer drains properly. Usually, the filter is accessed behind a front panel on the bottom of the washer and is easily twisted and removed for cleaning.

    Sometimes, foreign objects or small pieces of clothing bypass a clogged filter and block the drain pump. When this happens, the washer wont drain properly. Consult your user manual to determine how to access the drain pump on your model machine and look for blockages. If there are no visible blockages, the drain pump may have failed and requires a professional assessment.

    Recommended Reading: Home Depot Dishwasher Drain Hose


    Most Popular